!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE |
| PROBABLE CAUSE |
| SUGGESTED REMEDY |
|
|
|
|
|
1. Fan will not start. | 1. | Fuse or circuit breaker blown. | 1. | Check main and branch circuit fuses or circuit breakers. |
| 2. | Loose power line connections to the fan, or loose | 2. | Check line wire connections to fan and switch wire |
|
| switch wire connections in the switch housing. |
| connections in the switch housing. |
|
|
| ! | WARNING: Make sure main power is turned off. |
| 3. | The remote control transmitter battery needs | 3. | Check that the remote transmitter battery is in good |
|
| replacement. |
| condition; the red indicator will illuminate when the key |
|
|
|
| pad buttons are depressed. |
|
|
|
|
|
2. Fan sounds noisy. | 1. | Blades not attached to fan. | 1. | Attach blades to fan before operating. |
| 2. | Screws securing fan blade flanges to motor are | 2. | Check to make sure the screws which attach the fan |
|
| loose. |
| flanges to the motor are tight. |
| 3. | Screws holding blades to flanges are loose. | 3. | Tighten screws securely. |
| 4. | Glass bowl loose. | 4. | Tighten the glass bowl securely. |
|
|
|
|
|
3. Fan wobbles | 1. | Setscrew in motor coupling is loose. | 1. | Raise coupler cover and tighten the setscrew securely. |
excessively. | 2. | Setscrew in hanger ball/downrod assembly is | 2. | Tighten the setscrew in the hanger ball/downrod assembly. |
|
| loose. |
|
|
| 3. | Screws securing fan blade flanges to motor are | 3. | Check to be sure screws which attach the fan blade |
|
| loose. |
| flanges to the motor are tight. |
| 4. | Fan blade flanges not seated properly. | 4. | Check to be sure the fan blade flanges seat firmly and |
|
|
|
| uniformly to the surface of the motor. If flanges are |
|
|
|
| seated incorrectly, loosen the flange screws and retighten |
|
|
|
| according to the procedure in the section on "How to Put |
|
|
|
| Your Ceiling Fan Together". |
| 5. | Hanger bracket and/or ceiling outlet box is not | 5. | Tighten the hanger bracket screws to the outlet box, |
|
| securely fastened. |
| and/or secure outlet box. |
| 6. | Fan blades out of balance. | 6. | Interchanging an adjacent |
|
|
|
| redistribute the weight and result in smoother operation. |
|
|
|
|
|
4. All four lamps will not | 1. | The remote control transmitter battery needs | 1. | Replace the 12 V battery; recommended replacement |
illuminate. |
| replacement. |
| 12V batteries are Duracell MN21, Eveready A23, and |
|
|
|
| GP23A. |
|
|
| ! | WARNING: Make sure main power is turned off. |
| 2. | The 1.0 amp lamp fuse may have blown and | 2. | Replace the 1.0 amp fuse with Emerson repair part |
|
| and needs replacement. |
| item 19. See page 5 and reverse the lower housing |
|
|
|
| installation instructions to gain access to the fuse holder. |
|
|
|
|
|
9 | U.L. Model No.: CF955 |