Husqvarna 325P5X manual Cooling system, Spark plug, Air filter, Cleaning the air filter

Page 25

MAINTENANCE

CAUTION! Never use a machine with a defective muffler.

WARNING! Mufflers fitted with catalytic

!converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

4

3

2

1

The cooling system consists of:

1Air intake on the starter.

2Fins on the flywheel.

3Cooling fins on the cylinder.

4Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Spark plug

The spark plug condition is influenced by:

Incorrect carburettor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check

that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts.

Excessive fuel consumption.

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refitting it.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter.

English – 25

Image 25
Contents 323P4 325P5X-series Symbols KEY to SymbolsContents Dear Customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsStop switch Machine′s safety equipmentThrottle lock Vibration damping systemMuffler Specification of bar and saw chain Cutting equipmentBar Chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth With a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceSharpening cutting teeth If the raker clearance is too largeLubricating cutting equipment Tensioning the chainWhat to do if lubrication does not work Checking wear on cutting equipment ChainChain drive sprocket Increase the risk of accidentsAssembly Fitting the impact guard 325P5 Assembly of the saw attachment 325P5Dismantling Fuel Handling Fuel safetyFuel Transport and storageTwo-stroke oil FuellingMixing Petrol, litre Two-stroke oil LitreCheck before starting Starting and StoppingStarting and stopping Cold engineStopping StartingSafety instructions while working Safety instructions regarding the surroundingsWorking Techniques General working instructionsBasic working techniques Safety instructions after completing workWithout having the cutting attachment in full view Carburettor MaintenanceCorrectly adjusted carburettor Fine adjustment of the idle speed TMuffler High speed jet HCooling system Cleaning the air filterSpark plug Air filterOiling the air filter Maintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataBar and chain combinations EC-declaration of conformityApplies to Europe only Attachments Art No Use with´z+HB,¶6R¨ Page 1140341-26 ´z+HB,¶6R¨ ´z+HB,¶6R¨