Husqvarna 325P5X manual General Safety Precautions, Personal protective equipment

Page 6

GENERAL SAFETY PRECAUTIONS

Important

IMPORTANT!

The machine is only designed for cutting branches and twigs.

Never use a machine that has been modified in any way from its original specification.

Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Never use the machine in extreme weather conditions such as severe cold, very hot and/or humid climates.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance.

All covers and guards must be fitted before starting. Ensure that the spark plug cap and ignition lead are undamaged to avoid the risk of electric shock.

WARNING! Never allow children to use or be

!in the vicinity of the machine. As the machine is equipped with a spring-loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Personal protective equipment

IMPORTANT!

A pole saw is a dangerous tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely important that you read and understand the contents of this Operator’s Manual.

You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

WARNING! Listen out for warning signals or

!shouts when you are wearing hearing protection. Always remove your hearing protection as soon as the engine stops.

PROTECTIVE HELMET AND VISOR

HEARING PROTECTION

Wear hearing protection that provides adequate noise reduction.

EYE PROTECTION

Blows from branches or objects that are thrown out by a cutting attachment can damage the eyes.

GLOVES

Gloves should be worn when necessary, e.g., when fitting cutting attachments.

BOOTS

Wear sturdy, non-slip boots.

CLOTHING

Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.

FIRST AID KIT

Always have a first aid kit nearby.

6 – English

Image 6
Contents 323P4 325P5X-series KEY to Symbols SymbolsContents Introduction Dear CustomerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentThrottle lock Machine′s safety equipmentStop switch Vibration damping systemMuffler Cutting equipment Specification of bar and saw chainBar General information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceChain With a badly sharpened chainSharpening cutting teeth General advice on setting raker clearanceSetting the raker clearance If the raker clearance is too largeTensioning the chain Lubricating cutting equipmentChain drive sprocket Checking wear on cutting equipment ChainWhat to do if lubrication does not work Increase the risk of accidentsAssembly Assembly of the saw attachment 325P5 Fitting the impact guard 325P5Dismantling Fuel Fuel safetyFuel Handling Transport and storageMixing FuellingTwo-stroke oil Petrol, litre Two-stroke oil LitreStarting and stopping Starting and StoppingCheck before starting Cold engineStarting StoppingWorking Techniques Safety instructions regarding the surroundingsSafety instructions while working General working instructionsSafety instructions after completing work Basic working techniquesWithout having the cutting attachment in full view Maintenance CarburettorMuffler Fine adjustment of the idle speed TCorrectly adjusted carburettor High speed jet HSpark plug Cleaning the air filterCooling system Air filterOiling the air filter Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApplies to Europe only EC-declaration of conformityBar and chain combinations Attachments Art No Use with´z+HB,¶6R¨ Page 1140341-26 ´z+HB,¶6R¨ ´z+HB,¶6R¨