Hobart Welding Products OM-227 978B manual Operation, Controls

Page 23

SECTION 6 − OPERATION

6-1. Controls

1

5

3

1 Wire Speed Control

2

Power Switch

 

3

Voltage Switch

Use control to select a wire feed speed. As

 

The higher the selected number, the

Voltage switch setting increases, wire

thicker the material that can be welded

speed range also increases (see weld

(see weld setting label in welding power

setting label in welding power source or

source or Section 6-2, as applicable). Do

Section 6-2, as applicable).

not switch under load.

2

4

Ref. 227 950-A

.Switch must “click” into detent position.

4 Over Temperature Light

Light illuminates if main transformer overheats.

5 Gun Trigger Receptacle

OM-227 978 Page 19

Image 23
Contents 2007−04 OM-227 978BProcesses DescriptionFrom Hobart to You Table of Contents Typical MIG Process Connections − Parts List− MIG Welding Gmaw Guidelines Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LE Soudage peut provoquer un incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone− Definitions − SpecificationsSymbols And Definitions SpecificationsOutput Duty Cycle And OverheatingVolt-Ampere Curves AmperesInstalling Work Clamp − InstallationInstalling Welding Gun Changing Polarity Process/Polarity TableInstalling Gas Supply Selecting a Location And Connecting Input Power Tools Needed Electrical Service GuideInstalling Wire Spool And Adjusting Hub Tension Installing Contact Tip And Nozzle Appropriate setting Connecting Optional Spool GunThreading Welding Wire Controls − OperationWeld Parameter Chart For 230 VAC Model 227 949-B Months − Maintenance &TROUBLESHOOTINGRoutine Maintenance Overload Protection Drive Motor Protection030/.035 Groove Stamped 023/.025 Groove Stamped .030/.035 Changing Drive Roll Or Wire Inlet GuideTurn Off power before replacing contact tip Replacing Gun Contact TipTo Reassemble Gun Cleaning Or Replacing Gun LinerDisconnect gun from unit Replacing Switch And/Or Head Tube Trouble Remedy Troubleshooting TableOM-227 978 Circuit Diagram − Electrical Diagram227 951-B Typical MIG Process Connections − MIG Welding Gmaw GuidelinesAmperage Typical MIG Process Control SettingsWire Size Amperage Range Thickness to Amperage aHolding And Positioning Welding Gun Short Normal Long Conditions That Affect Weld Bead ShapePush Perpendicular DragGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Possible Causes Corrective Actions Troubleshooting − Excessive SpatterTroubleshooting − Porosity Troubleshooting − Excessive PenetrationTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Weld bead Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Common MIG Shielding GasesTroubleshooting Guide For Semiautomatic Welding Equipment OM-227 978 Main Assembly − Parts ListDia Part Dia Part Mkgs Description Quantity 231 H-14 GunConsumables Optional Drive RollsOptions Page Work like a Pro Assistance ServiceSupport Hobart Welding Products Contact your Distributor for