Carrier 50RLP Global Dictionary, Loop Supply Water SETPT01, System Pressure SETPT02

PUMP 2 RUN TIME — This point displays the number of hours that the pump has run. When the maximum number of hours is exceeded (9999 hours), both pumps run time hours will reset to 0.

Pump 2 Run Time
Display Units	Numeric
Default Value	0
Display Range	0 to 9999
Network Access	Read/Write

Loop Supply Water Set Point — The low set point is the low limit the supply water temperature may drop down to before the heat source will be activated to maintain the Loop Supply water temperature. The high set point is the high limit the supply water may rise to before the cooling source will be activated to maintain the loop supply water temperature. See Table 15. Set points can also be modified with slide bars in the ComfortVIEW™ software. See Fig. 11.

Table 15 — Loop Supply Water (SETPT01)

DESCRIPTION	VALUE	NAME
Occupied Lo Setpoint	60.00 df	OccLow
Occupied Hi Setpoint	90.00 df	OccHgh
Unoccupied Lo Setpoint	60.00 df	UnOccLow
Unoccupied Hi Setpoint	90.00 df	UnOccHgh
Occupied Low:
Configuration Units	degrees F (degrees C)
Configuration Range	–40.0 to 245.0
Default Value	60.0
Occupied High:
Configuration Units	degrees F (degrees C)
Configuration Range	–40.0 to 245.0
Default Value	90.0
Unoccupied Low:
Configuration Units	degrees F (degrees C)
Configuration Range	–40.0 to 245.0
Default Value	60.0
Unoccupied High:
Configuration Units	degrees F (degrees C)
Configuration Range	–40.0 to 245.0
Default Value	90.0

System Pressure Set Point — This set point defines the system pressure that the variable speed pumps will operate when the Aquazone™ system control panel is configured for variable speed pumping. See Table 16. Set points can also be modified with slide bars in the ComfortVIEW software. See Fig. 12.

Table 16 — System Pressure (SETPT02)

DESCRIPTION	VALUE	NAME
Occupied Lo Setpoint	10.00 PSIG	OccLow
Occupied Hi Setpoint	10.00 PSIG	OccHgh
Unoccupied Lo Setpoint	10.00 PSIG	UnOccLow
Unoccupied Hi Setpoint	10.00 PSIG	UnOccHgh

Occupied Low:
Configuration Units	PSIG
Configuration Range	–9999.9 to 9999.9
Default Value	10.0

Occupied High:
Configuration Units	PSIG
Configuration Range	–9999.9 to 9999.9
Default Value	10.0
Unoccupied Low:
Configuration Units	PSIG
Configuration Range	–9999.9 to 9999.9
Default Value	10.0
Unoccupied High:
Configuration Units	PSIG
Configuration Range	–9999.9 to 9999.9
Default Value	10.0
Global Dictionary — The	Global Dictionary table is
shown in Table 17.
Table 17 — Global Dictionary (AQUAMASC)
DESCRIPTION	VALUE	NAME
PUMPS 0=ON/OFF,1=VFD	0.00	PUMP_CFG
Pump Rotation Hours	50.00	ROT_TIME
TOWERS 0=STAGED,1=VFD	0.00	COOL_CFG
HEAT 0=STAGED,1=MOD/VFD	0.00	HEAT_CFG
Sched Bcst 0=N,1=Y	0.00	GLOBAL

PUMP CONTROL TYPE — This configuration determines how the pump outputs will be controlled. If the pump relays were ordered with the Aquazone system control panel, then the pump control type should be set to 0. If the pump outputs will control variable speed pumps, then the configuration should be set to 1. When variable speed control is selected, both outputs will control simultaneously.

Pump Control Type:
Configuration Units	None
Configuration Range	0 or 1
Default Value	0

PUMP ROTATION HOURS — When the pump control type is set to 0 (on/off), this configuration is used to set the maxi- mum number of hours the lead pump may accumulate beyond the numbers of hours accumulated for the lag pump. When this difference in hours is reached, the lead pump will change to the pump with the lesser number of accumulated run hours.

Pump Rotation Hours:
Configuration Units	HOURS
Configuration Range	0 to 9999
Default Value	50.0

TOWER/COOLING SOURCE CONTROL TYPE — This configuration determines how the tower outputs will be con- trolled. If panels were ordered with the stage output transducers, then tower control type should be set to 0. If the tower outputs will control variable speed tower fans, then the configuration should be set to 1.

Variable speed configuration will control both outputs si- multaneously.

Tower/Cooling Source Control Type:

Configuration Units	None
Configuration Range	0 or 1
Default Value	0

24