Grizzly G0632 owner manual Tool rest installed on the tool rest Base

Page 19

3.Secure the lathe assembly to the supporting legs with the (8) M10-1.5 x 25 cap screws and 10mm flat washers (see Figure 12).

Figure 12. Securing lathe assembly to

supporting legs.

4.If you are bolting your lathe to the floor, skip to Step 7. Otherwise, move the tailstock, tool rest assembly, and headstock to one end of the lathe bed (see the OPERATIONS sec- tion beginning on Page 18 for instructions for moving these components).

5.Use assistants to lift the light end of the lathe onto support blocks in preparation for install- ing the machine feet (see Figure 13).

Support Blocks

Figure 13. Example of supporting one end of lathe in preparation for installing the machine feet.

Note: Use assistants to support and stabilize the lathe while you install the machine feet.

G0632 16" x 42" Variable Speed Wood Lathe

6.Insert the machine feet into the mounting holes of the supporting legs, as shown in Figure 14. Do not tighten the top hex nut yet. Repeat Steps 5–6on the other legs.

Figure 14. Machine feet installed.

7.Place a level on the lathe bed and make nec- essary adjustments so that the bed is level from side-to-side and front-to-back.

—If you are using the machine feet, adjust the top and bottom hex nuts on each leg to level the bed; then tighten the hex nuts to secure these adjustments.

—If you are bolting your lathe to the floor, use shims under the legs to level the bed; then tighten the mounting fasteners.

8.Insert the tool rest into the tool rest base and tighten the tool rest lock lever (see Figure 15).

		Tool Rest
	Tool Rest Base	Tool Rest
	Tool Rest Base	Lock Lever
		Lock Lever

Figure 15. Tool rest installed on the tool rest

base.

-17-

Image 19

Contents

Model G0632 16 X 42 Variable Speed Wood Lathe Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0632 16 x 42 Variable Speed Wood Lathe Identification Page G0632 16 x 42 Variable Speed Wood Lathe G0632 16 x 42 Variable Speed Wood Lathe G0632 16 x 42 Variable Speed Wood Lathe Additional Safety Instructions for Wood Lathes Circuit Requirements 220V Single-PhaseUnpacking SetupSetup Safety Items Needed for Setup Inventory Figures Qty InventoryHardware Recognition Chart Mounting to Shop Floor Site ConsiderationsAssembly Clean UpTo assemble your lathe Tool rest installed on the tool rest Base Test Run Operations Operation Safety Adjusting HeadstockTo position the headstock along the length of the lathe bed To swivel the headstock Adjusting TailstockTo position the tailstock along the length of the bed Adjusting Tool Rest To install the headstock center Installing/Removing Headstock CenterTo remove the headstock center with the knockout tool To install the center into the tailstock quill Installing/Removing Tailstock CenterTo remove the center from the tailstock quill Headstock Faceplate To install the headstock faceplateFaceplate Turning on Diameter Roughing General Finishing Work Changing Speed RangesTo change speed ranges Speed range belt positions Indexing pin and indexing holes IndexingSelecting Turning Tools Spindle Turning To set up a spindle turning operationG0632 16 x 42 Variable Speed Wood Lathe Spindle Turning Safety Tips To mount the workpiece onto the faceplate Faceplate TurningTo mount your workpiece to a backing block Sanding/Finishing Outboard TurningG1082-4-Jaw Chuck AccessoriesG1194-3-Jaw Chuck H9586-Lathe FundamentalsG9863-8-PC HSS Lathe Chisel Set Model H6542 Robert Sorby 8-PC SetLubrication MaintenanceCleaning Lathe Bed ScheduleTroubleshooting ServiceWood Lathe Operation Date Approximate Hours Of Use Service Performed Service LogTo change the belt Aligning CentersChanging Belt To align the centersElectrical Components Model G0632 RPM sensor wiringWiring Wiring Diagram OverviewFrequency Inverter Wiring Diagram Stand & Bed Parts Breakdown Description Stand & Bed Parts ListHeadstock Parts Breakdown Headstock Parts List Label Placement Warranty and Returns G0632 16 x 42 Variable Speed Wood Lathe Page Page