Grizzly G0632 owner manual Wood Lathe Operation

Page 40

Wood Lathe Operation

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

 

Vibration noise while

1.

Belt cavity cover(s) loose.

1.

Tighten the screws that mount the belt cavity

machine is running; noise

 

 

 

cover(s); if necessary install a soft, vibration damp-

changes when speed is

 

 

 

ening material between the belt cover and the head-

changed.

 

 

 

stock casting.

 

 

 

 

 

Vibration noise while

1.

Dented fan cover on motor.

1.

Replace or adjust fan cover. Inspect motor fan and

machine is running; noise

 

 

 

replace if damaged.

remains constant when

 

 

 

 

speed is changed.

 

 

 

 

 

 

 

 

 

Excessive vibration.

1.

Workpiece mounted incorrectly.

1.

Re-mount workpiece, making sure that centers are

 

 

 

 

embedded in true center of workpiece.

 

2.

Workpiece warped, out of round, or

2.

Cut workpiece to correct, or use a different

 

 

is flawed.

 

workpiece.

 

3.

Spindle speed is set too fast for

3.

Reduce the spindle speed.

 

 

mounted workpiece.

 

 

 

4.

Lathe is resting on an uneven sur-

4.

Shim stand or adjust feet on stand to remove any

 

 

face.

 

wobbles present in the stand.

 

5.

Motor mount bolts are loose.

5.

Tighten motor mount bolts.

 

6.

Belt is worn or damaged.

6.

Replace belt (see Page 38).

 

7.

Spindle bearings are worn.

7.

Replace spindle bearings.

 

 

 

 

 

Chisels grab or dig into

1.

Tool rest set too low.

1.

Set tool rest higher. See Page 30 for how to prop-

workpiece.

 

 

 

erly set the tool rest height.

 

2.

Tool rest set too far from workpiece.

2.

Move the tool rest closer to the workpiece. See

 

 

 

 

Page 30 for the proper workpiece/tool rest clear-

 

 

 

 

ance.

 

3.

Wrong chisel/tool being used.

3.

Use the correct chisel/tool; educate yourself by

 

 

 

 

reading books, trade magazines, or seeking help

 

 

 

 

from an experienced lathe operator.

 

4.

Chisel/tool dull.

4.

Sharpen or replace the chisel/tool you are using.

 

 

 

 

 

Bad surface finish.

1.

Wrong spindle speed.

1.

Use trial-and-error to find a better spindle speed.

 

2.

Dull chisel or wrong chisel being

2.

Sharpen chisel or try a different chisel.

 

 

used for the operation.

 

 

 

 

 

 

 

Inaccurate turning results

1.

Headstock and tailstock are not

1.

Realign the tailstock to the headstock (see Page

from one end of the

 

properly aligned with each other.

 

38).

workpiece to the other.

 

 

 

 

 

 

 

 

 

Tailstock moves.

1.

Tailstock mounting bolt loose.

1.

Tighten.

 

2.

Bed surface is oily or greasy.

2.

Clean bed surface to remove excess oil/grease.

 

 

 

 

 

Can't remove tapered tool

1.

Tailstock barrel had not retracted all

1.

Turn the barrel handwheel until it forces taper out of

from tailstock barrel.

 

the way back into the tailstock.

 

barrel.

 

2.

Debris was not removed from taper

2.

Always make sure that taper surfaces are clean.

 

 

before inserting into barrel.

 

 

-38-

G0632 16" x 42" Variable Speed Wood Lathe

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model G0632 16 X 42 Variable Speed Wood Lathe Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0632 16 x 42 Variable Speed Wood Lathe Identification Page G0632 16 x 42 Variable Speed Wood Lathe G0632 16 x 42 Variable Speed Wood Lathe G0632 16 x 42 Variable Speed Wood Lathe Additional Safety Instructions for Wood Lathes 220V Single-Phase Circuit RequirementsSetup Setup SafetyItems Needed for Setup UnpackingInventory Inventory Figures QtyHardware Recognition Chart Site Considerations Mounting to Shop FloorAssembly Clean UpTo assemble your lathe Tool rest installed on the tool rest Base Test Run Operations Operation Safety Adjusting HeadstockTo position the headstock along the length of the lathe bed To swivel the headstock Adjusting TailstockTo position the tailstock along the length of the bed Adjusting Tool Rest To install the headstock center Installing/Removing Headstock CenterTo remove the headstock center with the knockout tool To install the center into the tailstock quill Installing/Removing Tailstock CenterTo remove the center from the tailstock quill Headstock Faceplate To install the headstock faceplateFaceplate Turning on Diameter Roughing General Finishing Work Changing Speed RangesTo change speed ranges Speed range belt positions Indexing Indexing pin and indexing holesSelecting Turning Tools To set up a spindle turning operation Spindle TurningG0632 16 x 42 Variable Speed Wood Lathe Spindle Turning Safety Tips To mount the workpiece onto the faceplate Faceplate TurningTo mount your workpiece to a backing block Outboard Turning Sanding/FinishingAccessories G1194-3-Jaw ChuckH9586-Lathe Fundamentals G1082-4-Jaw ChuckModel H6542 Robert Sorby 8-PC Set G9863-8-PC HSS Lathe Chisel SetMaintenance Cleaning Lathe BedSchedule LubricationService TroubleshootingWood Lathe Operation Service Log Date Approximate Hours Of Use Service PerformedAligning Centers Changing BeltTo align the centers To change the beltModel G0632 RPM sensor wiring Electrical ComponentsWiring Diagram Overview WiringFrequency Inverter Wiring Diagram Stand & Bed Parts Breakdown Stand & Bed Parts List DescriptionHeadstock Parts Breakdown Headstock Parts List Label Placement Warranty and Returns G0632 16 x 42 Variable Speed Wood Lathe Page Page

G0632 specifications

The Grizzly G0632 is a versatile and powerful wood lathe, designed for both professional woodworkers and hobbyists seeking to expand their craft. Renowned for its robust construction and user-friendly features, the G0632 is ideal for turning bowls, spindles, and various wood projects.

One of the standout features of the Grizzly G0632 is its powerful 1 HP motor, which delivers consistent performance for a variety of turning applications. The motor is capable of running at variable speeds ranging from 450 to 3,200 RPM. This range offers woodworkers the flexibility to choose the optimal speed for their specific project, whether it be a delicate spindle or a larger, more robust bowl.

The lathe's bed is made from heavy-duty cast iron, providing exceptional stability and reducing vibration during operation. This is crucial in achieving smooth finishes on your workpieces. The robust construction also means that the G0632 can handle larger, heavier pieces of wood without compromising performance.

Another significant characteristic of the G0632 is its easy-to-use swivel headstock. This feature allows users to turn larger projects without the need for an extension, providing greater versatility in positioning the workpiece. The headstock can be locked in place to maintain accuracy during turning.

The G0632 also boasts a 12-inch swing capacity over the bed, allowing for turning objects up to 12 inches in diameter. Coupled with a 36-inch distance between centers, this lathe provides ample space for a range of projects, from small bowls to longer spindles.

In terms of technology, Grizzly has equipped the G0632 with a quick-release tailstock, which simplifies the process of adjusting and positioning your workpiece. It also features a 4-position indexing head, which is perfect for creating intricate designs and patterns on your work.

For added safety, the G0632 includes a sturdy handwheel for manual control, ensuring that users can operate the lathe comfortably and securely. Additionally, the lathe's overall design promotes ease of use, making it a great choice for both experienced woodworkers and newcomers.

In summary, the Grizzly G0632 wood lathe encapsulates quality and functionality, making it a valuable addition to any workshop. Its powerful motor, sturdy construction, and user-friendly features combine to provide an unparalleled turning experience. Whether you're crafting detailed spindles or larger projects, the G0632 is designed to meet your woodworking needs.
Top Page Image Contents