Delta 36-550, 36-560 w/stand) Blade Tilting Control, Adjusting 90 and 45 Degree Positive Stops

Page 17

BLADE TILTING CONTROL

To tilt the saw blade, loosen blade tilting lock handle (A) Fig. 45, move handwheel (B) until the blade is at the desired angle and tighten lock handle (A). NOTE: The lock handle (A) is spring-loaded and can be repositioned by pulling out on the handle (A) and repositioning it on the serrated stud located underneath the handle.

WARNING: THE BLADE TILTING LOCK HANDLE (A) MUST BE LOCKED DURING ALL CUTTING OPERATIONS.

A

B

Fig. 45

ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS

Your saw is equipped with positive stops for rapid and accurate positioning of the saw blade at 90 and 45 degrees to the table. To adjust the positive stops, proceed as follows:

1.DISCONNECT MACHINE FROM POWER SOURCE.

2.Raise the saw blade to its maximum height.

TO ADJUST POSITIVE STOP AT 90 DEGREES

3.Loosen the blade tilting lock handle, move the blade tilting mechanism as far as possible to the left and tighten the blade tilting lock handle.

4.Place a square (A) Fig. 46, on the table with one end of the square against the blade, as shown, and check to see if the blade is at 90 degrees to the table. If it is not, loosen screw (B) a few turns and move the blade tilting mechanism until the blade is at 90 degrees to the table. Then tighten blade tilting lock handle and tighten screw

(B) until it bottoms.

TO ADJUST POSITIVE STOP AT 45 DEGREES

5.Loosen the blade tilting lock handle, move the blade tilting mechanism as far as possible to the right and tighten the blade tilting lock handle.

6.Place a square (A) Fig. 47, on the table with one end of the square against the blade as shown, and check to see if the blade is at 45 degrees to the table. If it is not, loosen screw (C) a few turns and move the blade tilting mechanism until the blade is at 45 degrees to the table. Then tighten blade tilting lock handle and tighten screw

(C) until it bottoms.

A B

Fig. 46

A

C

Fig. 47

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Table Saw General Safety Rules Refer to them often Use them to instruct others Additional Safety Rules for Table SAWGrounding Instructions Power ConnectionsMotor Specifications Extension Cords Unpacking and CleaningTable SAW Parts Page For Model 36-560 only Assembling Blade Raising and Lowering Handwheel AssemblyAssembling Blade Guard and Splitter Assembly Page Assembling Guide Rail to SAW Assembling Extension WingMiter Gage Assembling RIP FenceAssembling Miter Gage Holder Disconnect Machine from Power SourceAssembling Outfeed Support Fastening SAW to a Supporting Surface Assembling Stand for Model 36-560 onlyAssembling SAW to Stand For Model 36-560 only Locking Switch OFF Position Operating Controls and AdjustmentsStarting Stopping SAW Overload ProtectionBlade Tilting Control Adjusting 90 and 45 Degree Positive StopsMiter Gage Operation and Adjustments RIP Fence Operation and AdjustmentsChanging the Blade Adjusting Blade Parallel to Miter Gage SlotsRipping OperationCROSS-CUTTING Using Auxiliary Wood Facing on RIP Fence Constructing a Featherboard Pushstick Accessories PARTS, Service or Warranty Assistance

36-560 w/stand), 36-550 specifications

The Delta 36-550 and Delta 36-560 are versatile table saws designed for both amateur woodworkers and seasoned professionals. These tools stand out in the market due to their robust features, reliability, and precision cutting capabilities.

One of the prominent features of the Delta 36-550 and 36-560 is their powerful motor. Both models are equipped with a 15-amp motor that provides ample power to handle a variety of wood types, from softwoods to hard species. This makes them suitable for a wide range of cutting applications, whether for general woodworking projects or more intricate tasks.

Both models come with a 10-inch blade diameter, allowing for significant cutting depth and width. The 36-550 offers a maximum cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees, while the 36-560 matches these specifications, ensuring that users have ample capacity for various wood thicknesses.

The precision fence system is another noteworthy characteristic. The exclusive Delta T2 tool-free fence system ensures smooth operation and accuracy, allowing woodworkers to make straight, clean cuts consistently. The fence is easy to adjust and locks securely, providing confidence during operation.

Safety is a crucial factor in woodworking, and both models incorporate several features to protect users. The blade guard system is transparent, allowing for visibility during cuts while providing necessary protection. Furthermore, the onboard storage for accessories, as well as a sturdy table design, facilitates a tidy workspace.

Both the Delta 36-550 and 36-560 come equipped with a heavy-duty steel stand, ensuring stability during use. The stand is designed for easy setup and provides a solid base, significantly reducing vibrations during operation. This characteristic enhances safety and improves overall cutting precision.

Additionally, both saws feature a dust port that connects to a vacuum system, promoting a clean working environment. Reducing dust not only keeps the workspace tidy but also improves visibility and safety during cutting operations.

In summary, the Delta 36-550 and 36-560 table saws combine power, precision, and safety into a robust package ideal for any woodworking enthusiast. With features like a reliable motor, precise fence system, enhanced safety protocols, and sturdy construction, these table saws stand out as excellent choices for anyone looking to elevate their woodworking projects.
Top Page Image Contents