Delta Comprehensive Guide to Rip Fence and Miter Gage Adjustments for Precision Cutting
Page 18

RIP FENCE OPERATION AND ADJUSTMENTS

1.To move the rip fence (A) Fig. 48, along the table, lift up fence locking lever (B), slide the fence to the desired location on the table and push down fence locking lever

(B) to lock the fence in position.

2.A pointer is supplied to indicate the distance the fence is positioned away from the saw blade. If an adjustment to the pointer is required, loosen the screw

(C) Fig. 48, that fastens the pointer to the fence bracket and adjust the pointer accordingly. Then, tighten screw

(C).

3.IMPORTANT: THE RIP FENCE MUST BE PROPERLY ALIGNED TO THE MITER GAGE SLOT IN ORDER TO PREVENT KICKBACK WHEN RIPPING.

4.The saw blade is set parallel to the miter gage slot at the factory and the fence must be parallel to the miter gage slot in order to do accurate work and prevent kickback when ripping. To check the alignment:

5.Position the fence at one end of the miter gage slot, as shown in Fig. 48. Clamp the fence to the table by pushing down the locking lever (B). The edge of the fence should then line up parallel with the miter gage slot.

6.If an adjustment is necessary, proceed as follows:

C

A

D

F

E

B

Fig.48

7.Loosen the two screws (D) Fig. 48, and lift up locking lever (B). Then while holding the fence bracket (F) firmly toward the front of the saw, move the rear end of the fence (A) until it is parallel with the miter gage slot. Then tighten two screws (D) and push down locking lever (B).

8.The clamping action of the fence (A) Fig. 48, can be adjusted by lifting up locking lever (B) and turning screw

(E) clockwise to increase or counterclockwise to decrease the clamping action of the fence.

MITER GAGE OPERATION AND ADJUSTMENTS

When straight cross-cutting (blade set 90 degrees to the table) the miter gage can be used in either table slot. When bevel cross-cutting (blade tilted) only use the miter gage in the right table slot where the blade is tilted away from the miter gage and your hands.

This miter gage is equipped with individually adjustable index stops at 90 degrees and 45 degrees right and left. Adjustment to the index stops can be made by loosening lock nuts (B) Fig. 49, and tightening or loosening the three adjusting screws (C) until they contact the other end of stop pin (D) when the miter gage is at 90 and 45 degrees to the saw blade. Then, tighten lock nuts (B).

To operate the miter gage, simply loosen lock knob (E) Fig. 49, and move the body of the miter gage to the desired angle. When the stop pin (D) is pushed in, the miter gage body will stop at 90 degrees and 45 degrees right and left. To rotate the miter gage body past these points, pull out stop pin (D).

E

C

B

D

C B C B

Fig.49

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Table Saw General Safety Rules Additional Safety Rules for Table SAW Refer to them often Use them to instruct othersPower Connections Motor SpecificationsGrounding Instructions Unpacking and Cleaning Table SAW PartsExtension Cords Page For Model 36-560 only Assembly Assembling Blade Raising and Lowering HandwheelAssembling Blade Guard and Splitter Assembly Page Assembling Extension Wing Assembling Guide Rail to SAWAssembling RIP Fence Miter GageDisconnect Machine from Power Source Assembling Miter Gage HolderAssembling Outfeed Support Assembling Stand for Model 36-560 only Assembling SAW to Stand For Model 36-560 onlyFastening SAW to a Supporting Surface Starting Stopping SAW Operating Controls and AdjustmentsLocking Switch OFF Position Overload ProtectionAdjusting 90 and 45 Degree Positive Stops Blade Tilting ControlRIP Fence Operation and Adjustments Miter Gage Operation and AdjustmentsAdjusting Blade Parallel to Miter Gage Slots Changing the BladeOperation CROSS-CUTTINGRipping Using Auxiliary Wood Facing on RIP Fence Constructing a Featherboard Pushstick Accessories PARTS, Service or Warranty Assistance

36-560 w/stand), 36-550 specifications

The Delta 36-550 and Delta 36-560 are versatile table saws designed for both amateur woodworkers and seasoned professionals. These tools stand out in the market due to their robust features, reliability, and precision cutting capabilities.

One of the prominent features of the Delta 36-550 and 36-560 is their powerful motor. Both models are equipped with a 15-amp motor that provides ample power to handle a variety of wood types, from softwoods to hard species. This makes them suitable for a wide range of cutting applications, whether for general woodworking projects or more intricate tasks.

Both models come with a 10-inch blade diameter, allowing for significant cutting depth and width. The 36-550 offers a maximum cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees, while the 36-560 matches these specifications, ensuring that users have ample capacity for various wood thicknesses.

The precision fence system is another noteworthy characteristic. The exclusive Delta T2 tool-free fence system ensures smooth operation and accuracy, allowing woodworkers to make straight, clean cuts consistently. The fence is easy to adjust and locks securely, providing confidence during operation.

Safety is a crucial factor in woodworking, and both models incorporate several features to protect users. The blade guard system is transparent, allowing for visibility during cuts while providing necessary protection. Furthermore, the onboard storage for accessories, as well as a sturdy table design, facilitates a tidy workspace.

Both the Delta 36-550 and 36-560 come equipped with a heavy-duty steel stand, ensuring stability during use. The stand is designed for easy setup and provides a solid base, significantly reducing vibrations during operation. This characteristic enhances safety and improves overall cutting precision.

Additionally, both saws feature a dust port that connects to a vacuum system, promoting a clean working environment. Reducing dust not only keeps the workspace tidy but also improves visibility and safety during cutting operations.

In summary, the Delta 36-550 and 36-560 table saws combine power, precision, and safety into a robust package ideal for any woodworking enthusiast. With features like a reliable motor, precise fence system, enhanced safety protocols, and sturdy construction, these table saws stand out as excellent choices for anyone looking to elevate their woodworking projects.
Top Page Image Contents