Delta 36-560 w/stand), 36-550 Power Connections, Motor Specifications, Grounding Instructions

Page 4

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the motor to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the motor.

WARNING: DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

WARNING: THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

WARNING: IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A

Fig. B

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Table Saw General Safety Rules Additional Safety Rules for Table SAW Refer to them often Use them to instruct othersMotor Specifications Power ConnectionsGrounding Instructions Table SAW Parts Unpacking and CleaningExtension Cords Page For Model 36-560 only Assembly Assembling Blade Raising and Lowering HandwheelAssembling Blade Guard and Splitter Assembly Page Assembling Extension Wing Assembling Guide Rail to SAWAssembling RIP Fence Miter GageDisconnect Machine from Power Source Assembling Miter Gage HolderAssembling Outfeed Support Assembling SAW to Stand For Model 36-560 only Assembling Stand for Model 36-560 onlyFastening SAW to a Supporting Surface Operating Controls and Adjustments Locking Switch OFF PositionStarting Stopping SAW Overload ProtectionAdjusting 90 and 45 Degree Positive Stops Blade Tilting ControlRIP Fence Operation and Adjustments Miter Gage Operation and AdjustmentsAdjusting Blade Parallel to Miter Gage Slots Changing the BladeCROSS-CUTTING OperationRipping Using Auxiliary Wood Facing on RIP Fence Constructing a Featherboard Pushstick Accessories PARTS, Service or Warranty Assistance

36-560 w/stand), 36-550 specifications

The Delta 36-550 and Delta 36-560 are versatile table saws designed for both amateur woodworkers and seasoned professionals. These tools stand out in the market due to their robust features, reliability, and precision cutting capabilities.

One of the prominent features of the Delta 36-550 and 36-560 is their powerful motor. Both models are equipped with a 15-amp motor that provides ample power to handle a variety of wood types, from softwoods to hard species. This makes them suitable for a wide range of cutting applications, whether for general woodworking projects or more intricate tasks.

Both models come with a 10-inch blade diameter, allowing for significant cutting depth and width. The 36-550 offers a maximum cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees, while the 36-560 matches these specifications, ensuring that users have ample capacity for various wood thicknesses.

The precision fence system is another noteworthy characteristic. The exclusive Delta T2 tool-free fence system ensures smooth operation and accuracy, allowing woodworkers to make straight, clean cuts consistently. The fence is easy to adjust and locks securely, providing confidence during operation.

Safety is a crucial factor in woodworking, and both models incorporate several features to protect users. The blade guard system is transparent, allowing for visibility during cuts while providing necessary protection. Furthermore, the onboard storage for accessories, as well as a sturdy table design, facilitates a tidy workspace.

Both the Delta 36-550 and 36-560 come equipped with a heavy-duty steel stand, ensuring stability during use. The stand is designed for easy setup and provides a solid base, significantly reducing vibrations during operation. This characteristic enhances safety and improves overall cutting precision.

Additionally, both saws feature a dust port that connects to a vacuum system, promoting a clean working environment. Reducing dust not only keeps the workspace tidy but also improves visibility and safety during cutting operations.

In summary, the Delta 36-550 and 36-560 table saws combine power, precision, and safety into a robust package ideal for any woodworking enthusiast. With features like a reliable motor, precise fence system, enhanced safety protocols, and sturdy construction, these table saws stand out as excellent choices for anyone looking to elevate their woodworking projects.
Top Page Image Contents