Delta 36-312 Adjusting the Bevel Lock, Adjusting Sliding FIT Between Trunnion and Bevel Bracket

Page 11

DISCONNECT THE MACHINE FROM THE POWER SOURCE.

1.Position the bevel detent plate so that the desired angle (A) Fig. 25 is exposed.

2.Lift the front handle (A) Fig. 26 to disengage the bevel lock.

3.Tilt the cuttinghead left until it stops on the plate (B) Fig. 25.

4.To adjust, loosen the pin locking set screw (C) Fig. 27 (shown from the rear), located on the side of the trunnion and rotate the bushing (B) to the desired location. Rotate the bushing clockwise to decrease and counterclockwise to increase the bevel angle. Tighten screw (C) securely.

A

Fig. 26

NOTE: To perform a bevel cut more than 45°, pull bevel pin (B) Fig. 28 out to bypass the bevel detent plate. 48° is possible.

Make sure that the fence is clear of the guard and blade before operating the saw.

ADJUSTING THE BEVEL LOCK

The bevel-locking force has been set at the factory. After a period of time, you may need to adjust the locking mechanism. To adjust, place the bevel-locking handle (A) Fig. 26 in the “UP” position and tighten the nut (A) Fig. 29.

B

C

A

Fig. 27

A

Fig. 28

ADJUSTING SLIDING FIT BETWEEN TRUNNION AND BEVEL BRACKET

After a period of time, it may become necessary to adjust the sliding fit between the trunnion and the bevel bracket by tightening the adjusting nut (C) Fig. 29 at the rear of the tool.

Correct adjustment provides a snug sliding fit between these two parts. This adjustment should not be so tight that it restricts the tilting movement of the trunnion when bevel cutting, or so loose that it affects the accuracy of the saw cut.

ADJUSTING THE TENSION OF CUTTINGHEAD RETURN SPRING

The tension of the cuttinghead return spring has been adjusted at the factory so that the cuttinghead returns to the “up” position after a cut has been made. To re-adjust the spring tension, loosen the nut (A) Fig. 30 and turn the adjusting screw (B) Fig. 30 clockwise to increase, or counterclockwise to decrease the spring tension. Tighten nut (A) securely.

A

C

Fig. 29

ADJUSTING SLIDING FIT BETWEEN CUTTINGHEAD ARM AND TRUNNION

After a period of time, an adjustment of the sliding fit between the cuttinghead arm (B) Fig. 31, and the trunnion (C) may be necessary. To adjust, tighten or loosen the nut (D). Correct adjustment provides a snug sliding fit between these two parts. This adjustment should not be so tight that it restricts the sliding movement of the cuttinghead arm (B) or so loose that it affects the accuracy of the saw cut.

11

A

B

Fig. 30

B

DD

C

Fig. 31

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Single-Bevel Compound Miter Saw Important Safety Instructions Safety Guidelines DefinitionsGeneral Safety Rules Stay ALERT, Watch What YOU are Doing Failure to Follow These Rules MAY Result in Serious InjuryAdditional Safety Rules for Miter Saws Unpacking Power ConnectionsMotor Specifications Extension CordsMoving Cuttinghead to the UP Position ForewordAttaching Dust BAG ED E Moving Table to the 0 CUT-OFF PositionFence Operation Fastening Machine to Supporting SurfaceRotating Table for Miter Cutting Locking Switch in the OFF PositionConstructing Work Support Extensions Starting and Stopping MachineTable Hazard Zone Adjusting Sliding FIT Between Movable Table and BaseAdjusting Fence 90 to Blade Disconnect the Machine from the Power SourceSelecting 0, 33.9, and 45 Bevel Positive Stops Adjusting 0, 33.9, and 45 Bevel Positive StopsDisconnect Machine from Power Source Tilting Cuttinghead for Bevel CuttingAdjusting Sliding FIT Between Cuttinghead ARM and Trunnion Adjusting the Bevel LockAdjusting Sliding FIT Between Trunnion and Bevel Bracket Adjusting the Tension of Cuttinghead Return SpringCutting Aluminum Adjusting Lower Blade GuardTypical Operations and Helpful Hints Auxiliary Wood FenceCutting Crown Moulding Cutting Bowed MaterialChanging the Blade MaintenanceKeep Tool Clean Failure to StartBrush Inspection and Replacement AccessoriesTwo Year Limited New Product Warranty Arizona Illinois Minnesota Canadian PORTER-CABLE Delta Service Centers

36-312 specifications

The Delta 36-312 is a table saw that has gained a reputation among woodworkers and DIY enthusiasts for its robust performance and high-quality construction. This tool is designed for both professionals and hobbyists looking to achieve precise cuts in various materials, making it a versatile addition to any workshop.

One of the standout features of the Delta 36-312 is its powerful 15-amp motor, which provides ample power for handling a wide range of cutting tasks. This motor allows the saw to maintain consistent speeds even when cutting through denser materials, ensuring smooth, uniform results every time.

The design of the Delta 36-312 includes a massive cast iron table, which offers stability and durability while reducing vibration during operation. At 40 inches in length, the table provides ample workspace for larger projects and facilitates easier handling of sizable sheets of plywood or lumber. The surface finish is meticulously polished, promoting easy gliding of materials during cuts.

Another significant feature of the Delta 36-312 is its advanced fence system. The Biesemeyer-style fence is designed for quick and accurate adjustments, allowing users to make precise cuts quickly. This fence can be locked securely in place, ensuring that it will not shift during use, which is crucial for maintaining cutting accuracy.

The saw also integrates a riving knife technology that enhances safety by reducing the risk of kickback. This feature allows for smoother operation and is an essential aspect of modern table saw design. In addition, the saw includes a dust collection system that helps maintain a cleaner workspace by minimizing sawdust during operation.

For ease of transport and maneuverability, the Delta 36-312 is equipped with sturdy wheels, allowing it to be easily moved around the workshop or stored away when not in use. The assembly process is relatively straightforward, with most components easily fitting together without the need for specialized tools.

Overall, the Delta 36-312 represents a blend of power, precision, and safety features that cater to a wide range of woodworking needs. Its combination of a powerful motor, stable table, advanced fence system, and safety technologies makes it a standout choice for anyone serious about woodworking, whether they are professionals or hobbyists seeking to elevate their craft.
Top Page Image Contents