Delta 28-348 instruction manual Power Connections

Page 5

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A

Fig. B

 

5

Image 5
Contents Metal/Wood Cutting Band Saw Important Safety Instructions Safety Guidelines DefinitionsStay ALERT, Watch What YOU are DOING, Additional Safety Rules For Band Saws Power Connections Functional Description Unpacking and Cleaning Band SAW Parts Motor to Motor Bracket AssemblyMotor Bracket To Cabinet Dust Chute TOP Plate to CabinetDust Port Sure the Hinge Pins a are Pointed UP AS Shown in FigsStand Door to Stand Tighten the Screws AT this Time Hinge Opening is Pointing DownSAW to Stand Disconnect Machine from Power SourceMotor Pulley Belt to SAW and Motor PulleyAre Positioned AS Shown in FIG Table to SAWLength Blades Blade to SAWTable Insert On / OFF Switch To Stand Locking Switch in the OFF Position Operating Controls and AdjustmentsStarting Stopping SAW Tilting the TableTo adjust the 90 degree stop Adjusting Table StopsAdjusting Blade Tension Never Track the Blade While Tool is Running Tracking the BladeChanging Speeds Adjusting Lower Blade Guides and Blade Support BearingCD C OperationsCutting Curves Troubleshooting GuideTrouble Band SAW does not Come UP to Speed Suggested Metal Cutting Blades and Speeds Band SAW BladesLubrication MaintenanceChanging the Blades PARTS, Service or Warranty Assistance AccessoriesCanadian PORTER-CABLE Delta Service Centers