Delta 34-814, 34-806, 34-801 instruction manual Common Sawing Operations, Cross-Cutting

Page 18

422-04-651-0064 - 06-20-05.qxd 6/20/05 1:44 PM Page 18

MACHINE USE

COMMON SAWING OPERATIONS

Common sawing operations include ripping and crosscutting plus a few other standard operations of a fundamental nature. As with all power machines, there is a certain amount of hazard involved with the operation and use of the machine. Using the machine with the respect and caution demanded as far as safety precautions are concerned, will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury to the operator can result. The following information describes the safe and proper method for performing the most common sawing operations.

The use of attachments and accessories not recommended by Delta may result in the risk of injury to the user or others.

CROSS-CUTTING

Cross-cutting requires the use of the miter gauge to position and guide the work. Place the work against the miter gauge and advance both the gauge and work toward the saw blade, as shown in Fig. 46. The miter gauge may be used in either table slot. When bevel cutting (blade tilted), use the table groove that does not cause interference of your hand or miter gauge with the saw blade guard.

Start the cut slowly and hold the work firmly against the miter gauge and the table.

One of the rules in running a saw is that you never hang onto or touch the part of the workpiece that will be cut off. Hold the supported piece, not the free piece that is cut off. The feed in cross-cutting continues until the work is cut in two, and the miter gauge and work are pulled back to the starting point. Before pulling the work back, it is good practice to give the work a little sideways shift to move the work slightly away from the saw blade. Never pick up any short length of free work from the table while the saw is running. While blade is running, never touch a cut-off piece unless it is at least a foot long.

For added safety and convenience the miter gauge can be fitted with an auxiliary wood-facing (C), as shown in Fig. 47, that should be at least 1 inch higher than the maximum depth of cut, and should extend out 12 inches or more to one side or the other depending on which miter gauge slot is being used. This auxiliary wood-facing (C) can be fastened to the front of the miter gauge by using two wood screws (A) through the holes provided in the miter gauge body and into the wood-facing.

When using the block (B) Fig. 48, as a cut- off gauge, it is very important that the rear end of the block be positioned so the work piece is clear of the block before it enters the blade.

NEVER USE THE FENCE AS A CUT-OFF gauge WHEN CROSS-CUTTING.

When cross-cutting a number of pieces to the same length, a BLOCK OF WOOD (B), can be clamped to the fence and used as a cut-off gauge as shown in Fig. 48. It is important that this block of wood always be positioned in front of the saw blade as shown. Once the cut-off length is determined, secure the fence and use the miter gauge to feed the work into the cut. This block of wood allows the cut-off piece to move freely along the table surface without binding between the fence and the saw blade, thereby lessening the possibility of kickback and injury to the operator.

Fig. 46

A

C

Fig. 47

B

Fig. 48

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Unisaw 10 Right Tilting Arbor Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules Important Safety InstructionsAdditional Specific Safety Rules Failure to Follow These Rules MAY Result in Serious InjuryCarton Contents Functional DescriptionUnpacking and Cleaning 11AAssembly Time Estimate AssemblyAssembly Tools Required Installing the Blade Tilting HandwheelAttaching the LVC ON/OFF Switch Attaching the LVC Starter BOX to the CabinetWing Attaching the Magnetic Starter ON/OFF Switch Attaching the Blade Guard and Splitter AssemblyDisconnect the Machine from the Power Source 422-04-651-0064 06-20-05.qxd 6/20/05 142 PM 422-04-651-0064 06-20-05.qxd 6/20/05 143 PM Fastening the Motor Cord to the SAW Frame Attaching Motor CoverMiter Gauge Holder and Wrench Holder Attaching the RIP Fence Holder BracketsAttaching the Dust Chute Adapter Operation Adjusting 90 and 45 Degree Positive Stops Adjusting the TableDisconnect Machine from Power Source Adjusting the Table Insert Miter Gauge Operation and AdjustmentCommon Sawing Operations CROSS-CUTTINGRipping Constructing a Push StickRipping on Left Side of SAW Blade Accessory Moulding Cutterhead Using Moulding CutterheadUsing the Accessory Dado Head Using Auxiliary Wood Facing on RIP Fence Constructing a FeatherboardPushstick Troubleshooting Maintenance Replacing Belts and Adjusting Belt TensionChanging the SAW Blade Service AccessoriesWarranty Two Year Limited New Product WarrantyCanadian PORTER-CABLE Delta Service Centers
Related manuals
Manual 28 pages 38.89 Kb

34-801, 34-806, 34-814 specifications

Delta has long been a reputable name in the woodworking industry, and its line of table saws, including models such as the Delta 36-812, 34-814, 34-806, and 34-801, exemplifies the brand's commitment to quality and innovation. Each of these models offers unique features and technologies tailored to meet the needs of both professional woodworkers and hobbyists.

The Delta 36-812 is a compact yet powerful table saw designed for versatility and efficiency. This model features a 15-amp motor, capable of delivering 4,800 RPM, providing sufficient power for cutting through various materials including hardwood and softwood. One of the standout features of the 36-812 is its Portable Stand, which allows easy transportation and setup without compromising stability. The saw also boasts a large, adjustable rip fence, ensuring accuracy when making long cuts.

Next in line is the Delta 34-814, which takes things up a notch with its more advanced design. This cabinet saw is built with a one-piece, rigid steel frame that minimizes vibrations, contributing to cleaner cuts. The 34-814 also features a 1.5 HP motor, providing reliable power and performance in any workshop setting. Its patented Quick-Build T-Square System offers smooth adjustments for crosscuts and rip cuts, enhancing user convenience, while the large table surface provides plenty of workspace for larger projects.

For those looking for a reliable saw that combines performance with compactness, the Delta 34-806 makes a strong case. This model is equipped with a 1 HP motor and features a sturdy, lightweight construction which makes it ideal for smaller workshops or job sites. It boasts a patented fence system that is easy to use and adjust, along with a durable blade guard for enhanced safety. The compact design does not sacrifice cutting power, allowing woodworkers to tackle a variety of materials with ease.

Lastly, the Delta 34-801 is a classic contractor saw that captures the essence of performance and portability. It features a powerful 1.5 HP motor and a 30-inch rip capacity, perfect for larger woods and panels. The saw includes an easy-to-use rack and pinion fence system that improves accuracy and alignment. Its folding stand allows for effortless storage, making it a great option for those who need to maximize space.

In summary, the Delta 36-812, 34-814, 34-806, and 34-801 are all exemplary offerings in Delta's lineup, each designed with specific features and capabilities. From compact options to more robust cabinet designs, these saws cater to the diverse needs of woodworkers across various skill levels and applications. With their combination of power, precision, and innovative technologies, they continue to uphold Delta's legacy of excellence in woodworking tools.
Top Page Image Contents