Chicago Electric 98265 Recommended Minimum Wire Gauge for Extension Cords, Length, Table a

Page 3

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

EXTENSION CORD

AMPERES

 

LENGTH

 

(at full load)

25’

50’

100’

150’

0 – 6

18

16

16

14

6.1 – 10

18

16

14

12

10.1 – 12

16

16

14

12

12.1 – 16

14

12

Do not use.

TABLE A

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an exten- sion cord, be sure to use one heavy enough to carry the current your prod- uct will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.

13.DON’T OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and saf- est performance. Follow instructions for lubricating and changing accessories.

15.DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in.

17.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improp- er accessories may cause risk of injury to persons.

18.NEVER STAND ON TOOL. Serious inju- ry could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

19.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended func- tion – check for alignment of moving parts, binding of moving parts, break- age of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

20.DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

21.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

SKU 98265

For technical questions, please call 1-800-444-3353.

Page 3

Image 3
Contents HP 7 Bridge Tile SAW For technical questions or replacement parts, please callFor technical questions, please call General Tool Safety WarningsSave this Manual Save all warnings and instructions for future reference25’ 50’ 100’ 150’ Recommended Minimum Wire Gauge for Extension CordsNameplate Extension Cord Length125 V~ 3-Prong Plug and Outlet Tile Saw Safety WarningsGrounding Instructions 110-120 V~ Grounded Tools Tools With Three Prong PlugsSafe Method For technical questions, please call Stick Length Essential Straight Push-stick Features FunctionsDiagram not to scale Handle NotchExtension Cords Position of Tile SAWVibration Safety Save These Structions Unpacking SpecificationsList of contents AssemblyWork Piece and Work Area Set Up Operating InstructionsMounting Sliding Bar Support Bevel Scale General Operating InstructionsMaintenance Servicing Cleaning, Maintenance, LubricationChanging the Blade Troubleshooting Cleaning the SawProblem Possible Causes Likely Solutions Part Description Qty Parts List and Assembly Diagram a MotorPart Description Qty Parts List and Assembly Diagram B HangerParts List and Assembly Diagram C Support Part Description Parts List and Assembly Diagram D Work TableParts List and Assembly Diagram E Water Tray Limited 90 DAY Warranty