Black & Decker BDTS100 instruction manual Blade Tilt Adjustment, Degree Positive Stop Adjustments

Page 16

BLADE TILT ADJUSTMENT

To tilt the saw blade, loosen the lock handle (A) Fig. 30 and move the handwheel (B) until the blade is at the desired angle. Tighten the lock handle (A).

NOTE: The lock handle (A) is spring-loaded. Pull out on the handle (A) and reposition it on the serrated stud located underneath the handle.

THE BLADE TILTING LOCK HANDLE

(A)MUST BE LOCKED DURING ALL CUTTING OPERATIONS.

B

A

Fig. 30

90 AND 45 DEGREE POSITIVE STOP ADJUSTMENTS

Your saw is equipped with positive stops for rapid and accurate positioning of the saw blade at 90 and 45 degrees to the table.

DISCONNECT MACHINE FROM POWER SOURCE.

TO ADJUST POSITIVE STOP AT 90 DEGREES

 

1. Raise the saw blade to its maximum height.

 

2. Loosen the blade tilting lock handle (A) Fig. 30, move

 

the blade tilting mechanism (B) as far as possible to

 

the left, and tighten the blade tilting lock handle (A).

 

3. Place a square (A) Fig. 31 on the table with one end

B

of the square against the blade, and check to see if

 

the blade is 90 degrees to the table. If not, loosen the

A

screw (B) Fig. 31 a few turns and move the blade

tilting mechanism until the blade is 90 degrees to the

 

table. Tighten the blade tilting lock handle (A) Fig. 30,

 

and tighten the screw (B) Fig. 31 until it stops.

 

 

 

 

Fig. 31

TO ADJUST POSITIVE STOP AT 45 DEGREES

 

 

1. Raise the saw blade to its maximum height.

A

2. Loosen the blade tilting lock handle (A) Fig. 31, move

 

the blade tilting mechanism (B) as far as possible to

 

the right, and tighten the blade tilting lock handle (A).

 

3. Place a square (A) Fig. 32 on the table with one end

C

 

of the square against the blade, and see if the blade

 

is 45 degrees to the table. If not, loosen the screw

 

(C) Fig. 32 a few turns and move the blade tilting

 

mechanism (B) Fig. 30, until the blade is 45 degrees

 

to the table. Tighten the blade tilting lock handle (A)

 

Fig. 30, and tighten the screw (C) Fig. 32 until it

 

stops.

 

Fig. 32

 

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents BDTS100 10 254MM Table SAW Before Returning this Product For ANY Reason Please CallImportant Safety Instructions Table of ContentsSafety Guidelines Definitions California Proposition General Safety Rules USE of this Tool can GenerateAdditional Safety Rules for Table Saws Failure to Follow These Rules MAY Result in Serious InjuryMotor Specifications Power ConnectionsGrounding Instructions Carton Contents Functional DescriptionParts Assembly Unpacking and CleaningAssembly Tools Required Elevating and Supporting Surfaces for a SAW with no StandAssembling Stand SAW to StandAttaching Blade Height Adjusting Handwheel Attaching Blade Guard and Splitter AssemblyOn the screw L Fig Miter Gauge Attaching Miter Gauge HolderAssembling RIP Fence Illustrates the miter gauge D inserted into the holderLocking Switch in the OFF Position Blade Height AdjustmentOperation Starting and Stopping SAW45 Degree Positive Stop Adjustments Blade Tilt AdjustmentTo Adjust Positive Stop AT 45 Degrees RIP Fence Operation Adjustments Table Insert AdjustmentMiter Gauge Operation Adjustments Adjusting Blade Parallel to Miter Gauge SlotsChanging the Blade CROSS-CUTTINGRipping Constructing a Push StickUsing Auxiliary Wood Facing on RIP Fence Accessory Dado CutterheadDado Head SET Table Insert Pushstick Constructing a Push StickConstructing a Featherboard Maintenance TroubleshootingBanc DE Scie BDTS100 254 MM 10 PO Table DES Matières Directives DE Sécurité ImportantesLignes Directrices EN Matière DE Sécurité Définitions Proposition 65 DE LA CalifornieRègles Générales DE Sécurité Directives DE Sécurité ImportantesRègles DE Sécurité Supplémentaires Pour LES Bancs DE Scie Conserver CES DirectivesCaractéristiques Techniques DU Moteur Connexions ÉlectriquesDirectives DE Mise À LA Terre Rallonges Électriques Description FonctionnelleContenu DU Carton AVANT-PROPOSDésemballage ET Nettoyage AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Assemblage DU Socle Scie SUR SocleFixation DU Volant Servant À Régler LA Hauteur DE LA Lame Fixation DE L’ENSEMBLE PARE-MAIN/COUTEAU SéparateurFonctionnement Jauge À OngletFixation DU Support DE LA Jauge À Onglet Assemblage DU Guide LongitudinalVerrouiller L’INTERRUPTEUR EN Position D’ARRET Réglage DE LA Hauteur DE LA LameRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésUtilisation DE LA Jauge À Onglet ET Réglages Réglage DE Linsert DE TableChangement DE LA Lame Tronçonnage Sciage EN LongFraise Accessoire À Rainurer Construire UN Poussoir EntretienConstruire UNE Planche EN Éventail Dépannage Quel EST LE Problème ? QUE FAIRE…555326-7100 Índice Instrucciones Importantes Sobre SeguridadNormas DE Seguridad Definiciones LA Propuesta 65 DE CaliforniaNormas Generales DE Seguridad Instrucciones Importantes Sobre SeguridadNormas DE Seguridad Adicionales Para LAS Sierras DE Mesa Mantenga LOS BRAZOS, LAS Manos y LOS Dedos lejos de la hojaEspecificaciones DEL Motor Conexiones EléctricasInstrucciones DE Conexión a Tierra Descripción DE LAS Funciones Contenido DE LA CajaCables Prolongadores IntroducciónMontaje Desembalaje Y LimpiezaHerramientas Necesarias Para EL Montaje Superficies DE Apoyo Y Elevación Para UNA Sierra SIN BaseSierra a LA Base Montaje DE LA BaseColocación DEL Volante Para Ajustar LA Altura DE LA Hoja Calibrador DE Inglete Colocación DEL Ensamble DE Guarda DE LA Hoja Y HedidorColocación DEL Sujetador DEL Calibrador DE Inglete Operación Ajustes DE Topes Positivos a 90 Y 45 Grados Operación DE LA Guía DE Corte Y AjustesAjuste DEL Inserto Para Mesa Ajustar UN Tope Positivo a 45 GradosOperación DEL Calibrador DE Inglete Y Ajustes Cambio DE LA HojaCorte Longitudinal Corte TransversalVara Para Empujar Construcción DE UN Palo DE Empujar Cabezal Portacuchilla Accesorio Para RanurasConstrucción DE UNA Tabla DE Canto Biselado Detección DE Problemas MantenimientoInformación de mantenimiento

BDTS100 specifications

The Black & Decker BDTS100 is a versatile and highly efficient oscillating tool designed for homeowners and professionals alike. Capable of tackling a wide range of projects, the BDTS100 stands out due to its innovative technologies and user-centric features.

One of the main attributes of the BDTS100 is its powerful motor, which delivers an impressive performance while maintaining user comfort. The 2.5 amp motor operates at varying speeds, ensuring optimal control for different applications. This functionality is especially useful for tasks ranging from sanding to cutting, allowing users to adjust the tool's performance based on the materials and requirements at hand.

Versatility is a hallmark of the BDTS100. It comes equipped with a quick-change accessory system that enables users to switch between various attachments with ease. This system significantly reduces downtime, allowing for seamless transitions when moving from one task to another. The oscillating motion of the BDTS100 allows for smooth cuts without the risk of kickback, making it a safe option for both novice and experienced users.

The BDTS100 also features an ergonomic design that offers comfort during prolonged use. The slim, lightweight body ensures that users can maneuver the tool in tight spaces without sacrificing control. Additionally, the rubberized grip provides added comfort and reduces vibrations, allowing for extended use without fatigue.

In terms of technological advancements, the BDTS100 benefits from Black & Decker's commitment to innovation. The integrated dust extraction port helps keep work areas clean, while also enhancing visibility when cutting or sanding. This feature is especially important for users concerned about maintaining a tidy workspace or for those working on detailed projects.

Moreover, the BDTS100 is compatible with a wide range of accessories, making it adaptable for various tasks, including sanding, grinding, scraping, and cutting. Whether tackling home improvement projects or professional tasks, this oscillating tool is designed to meet a variety of needs.

In conclusion, the Black & Decker BDTS100 is a powerful, versatile, and user-friendly oscillating tool. Its features, including a robust motor, quick-change accessory system, ergonomic design, and integrated dust extraction, make it an ideal choice for anyone looking to enhance their toolkit. Whether for a DIY project or professional work, the BDTS100 is engineered to deliver performance and convenience.
Top Page Image Contents