Black & Decker BDTS100 instruction manual Unpacking and Cleaning, Assembly Tools Required

Page 9

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

ASSEMBLY

ASSEMBLY TOOLS REQUIRED

* 13mm wrench for stand bolts

* 10mm wrench for splitter assembly bolts

(None supplied)

* Straight edge and/or framing square for adjustments

* Phillips head screwdriver

 

ASSEMBLY TIME ESTIMATE - 1 hour

ELEVATING AND SUPPORTING SURFACES FOR A SAW WITH NO STAND

THE SAW MUST BE PROPERLY SECURED TO A SUPPORTING SURFACE. ALSO, FAILURE TO PROVIDE A SAWDUST FALL-THROUGH AND REMOVAL HOLE WILL ALLOW SAWDUST TO BUILD UP AROUND THE MOTOR, CAUSING A POSSIBLE FIRE HAZARD AND/OR MOTOR DAMAGE.

DISCONNECT MACHINE FROM POWER SOURCE.

The saw must be elevated enough for sawdust to fall through the bottom of the saw and not build up around the motor.

Position the four mounting holes located on the base of the saw cabinet (two of which are shown at (A) Fig. 4A) over whatever proper support you are using. Then securely fasten the saw to the supports. The saw can be secured by fastening the stand through the mounting holes with suitable hardware (not supplied).

THE SAW SUPPORT MUST BE STABLE

AND ABLE TO SUPPORT 300 POUNDS.

You can also construct a simple elevated support, as shown in Fig. 4B.

USE A GOOD GRADE OF PLYWOOD WITH A MINIMUM 3/4" THICKNESS. DO NOT MAKE THE MOUNTING BOARD FROM PARTICLE BOARD SINCE PARTICLE BOARD BREAKS EASILY.

A HOLE MUST BE PROVIDED IN THIS SUPPORT TO ALLOW SAWDUST TO FALL THROUGH.

Square the saw on the supporting surface and mark the location for four 5/16 inch holes to be drilled (Fig. 4B).

MAKE SURE THERE IS AT LEAST 3"

ON ALL FOUR SIDES OF THE BASE.

Set the saw aside and then drill holes in these marks. Locate and mark an 11" or 12" square centered between the four mounting holes. Cut out and remove the square (Fig. 4B).

To elevate the supporting surface, measure two 2x4s

(A)Fig. 4B to the width of two opposite sides of the supporting surface. Attach the supporting surface to the narrow edges of the 2X4s (as shown in Fig. 4B) using wood screws (not provided) in at least three spots (B) Fig. 4B on each side.

A

Fig. 4A

SAW PLACEMENT

 

5/16" PILOT

 

 

B

 

HOLES

 

 

MARKS

 

 

 

 

 

 

 

 

3"

MINIMUM

 

3"

 

 

 

 

 

 

 

 

 

 

 

MINIMUM

 

 

 

12"

 

 

 

 

 

11"OR

 

 

 

 

 

 

 

 

 

 

 

SQUARE

 

 

 

 

 

 

CUTOUT

 

MINIMUM

 

 

 

 

3"

 

3"

 

 

 

 

 

MINIMUM

 

 

 

 

 

 

 

 

B

 

 

 

 

 

A

 

 

 

 

 

 

Fig. 4B

Fasten the saw to the surface by inserting suitable hardware (not supplied) through the mounting holes on the saw and into the previously drilled holes. While using the saw, periodically remove the sawdust buildup from below the saw.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Before Returning this Product For ANY Reason Please Call BDTS100 10 254MM Table SAWTable of Contents Important Safety InstructionsSafety Guidelines Definitions California Proposition USE of this Tool can Generate General Safety RulesFailure to Follow These Rules MAY Result in Serious Injury Additional Safety Rules for Table SawsPower Connections Motor SpecificationsGrounding Instructions Functional Description Carton ContentsParts Unpacking and Cleaning AssemblyAssembly Tools Required Elevating and Supporting Surfaces for a SAW with no StandSAW to Stand Assembling StandAttaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Attaching Miter Gauge Holder Miter GaugeIllustrates the miter gauge D inserted into the holder Assembling RIP FenceBlade Height Adjustment Locking Switch in the OFF PositionOperation Starting and Stopping SAWBlade Tilt Adjustment 45 Degree Positive Stop AdjustmentsTo Adjust Positive Stop AT 45 Degrees Table Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Changing the BladeConstructing a Push Stick RippingAccessory Dado Cutterhead Using Auxiliary Wood Facing on RIP FenceDado Head SET Table Insert Constructing a Push Stick PushstickConstructing a Featherboard Troubleshooting MaintenanceBanc DE Scie BDTS100 254 MM 10 PO Directives DE Sécurité Importantes Table DES MatièresLignes Directrices EN Matière DE Sécurité Définitions Proposition 65 DE LA CalifornieDirectives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Supplémentaires Pour LES Bancs DE ScieConnexions Électriques Caractéristiques Techniques DU MoteurDirectives DE Mise À LA Terre Description Fonctionnelle Rallonges ÉlectriquesContenu DU Carton AVANT-PROPOSAssemblage Désemballage ET NettoyageOutils Nécessaires Pour L’ASSEMBLAGE Scie SUR Socle Assemblage DU SocleFixation DU Volant Servant À Régler LA Hauteur DE LA Lame Fixation DE L’ENSEMBLE PARE-MAIN/COUTEAU SéparateurJauge À Onglet FonctionnementFixation DU Support DE LA Jauge À Onglet Assemblage DU Guide LongitudinalRéglage DE LA Hauteur DE LA Lame Verrouiller L’INTERRUPTEUR EN Position D’ARRETRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésRéglage DE Linsert DE Table Utilisation DE LA Jauge À Onglet ET RéglagesChangement DE LA Lame Sciage EN Long TronçonnageFraise Accessoire À Rainurer Entretien Construire UN PoussoirConstruire UNE Planche EN Éventail Quel EST LE Problème ? QUE FAIRE… Dépannage555326-7100 Instrucciones Importantes Sobre Seguridad ÍndiceNormas DE Seguridad Definiciones LA Propuesta 65 DE CaliforniaInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadMantenga LOS BRAZOS, LAS Manos y LOS Dedos lejos de la hoja Normas DE Seguridad Adicionales Para LAS Sierras DE MesaConexiones Eléctricas Especificaciones DEL MotorInstrucciones DE Conexión a Tierra Contenido DE LA Caja Descripción DE LAS FuncionesCables Prolongadores IntroducciónDesembalaje Y Limpieza MontajeHerramientas Necesarias Para EL Montaje Superficies DE Apoyo Y Elevación Para UNA Sierra SIN BaseMontaje DE LA Base Sierra a LA BaseColocación DEL Volante Para Ajustar LA Altura DE LA Hoja Colocación DEL Ensamble DE Guarda DE LA Hoja Y Hedidor Calibrador DE IngleteColocación DEL Sujetador DEL Calibrador DE Inglete Operación Operación DE LA Guía DE Corte Y Ajustes Ajustes DE Topes Positivos a 90 Y 45 GradosAjuste DEL Inserto Para Mesa Ajustar UN Tope Positivo a 45 GradosCambio DE LA Hoja Operación DEL Calibrador DE Inglete Y AjustesCorte Transversal Corte LongitudinalVara Para Empujar Cabezal Portacuchilla Accesorio Para Ranuras Construcción DE UN Palo DE EmpujarConstrucción DE UNA Tabla DE Canto Biselado Mantenimiento Detección DE ProblemasInformación de mantenimiento

BDTS100 specifications

The Black & Decker BDTS100 is a versatile and highly efficient oscillating tool designed for homeowners and professionals alike. Capable of tackling a wide range of projects, the BDTS100 stands out due to its innovative technologies and user-centric features.

One of the main attributes of the BDTS100 is its powerful motor, which delivers an impressive performance while maintaining user comfort. The 2.5 amp motor operates at varying speeds, ensuring optimal control for different applications. This functionality is especially useful for tasks ranging from sanding to cutting, allowing users to adjust the tool's performance based on the materials and requirements at hand.

Versatility is a hallmark of the BDTS100. It comes equipped with a quick-change accessory system that enables users to switch between various attachments with ease. This system significantly reduces downtime, allowing for seamless transitions when moving from one task to another. The oscillating motion of the BDTS100 allows for smooth cuts without the risk of kickback, making it a safe option for both novice and experienced users.

The BDTS100 also features an ergonomic design that offers comfort during prolonged use. The slim, lightweight body ensures that users can maneuver the tool in tight spaces without sacrificing control. Additionally, the rubberized grip provides added comfort and reduces vibrations, allowing for extended use without fatigue.

In terms of technological advancements, the BDTS100 benefits from Black & Decker's commitment to innovation. The integrated dust extraction port helps keep work areas clean, while also enhancing visibility when cutting or sanding. This feature is especially important for users concerned about maintaining a tidy workspace or for those working on detailed projects.

Moreover, the BDTS100 is compatible with a wide range of accessories, making it adaptable for various tasks, including sanding, grinding, scraping, and cutting. Whether tackling home improvement projects or professional tasks, this oscillating tool is designed to meet a variety of needs.

In conclusion, the Black & Decker BDTS100 is a powerful, versatile, and user-friendly oscillating tool. Its features, including a robust motor, quick-change accessory system, ergonomic design, and integrated dust extraction, make it an ideal choice for anyone looking to enhance their toolkit. Whether for a DIY project or professional work, the BDTS100 is engineered to deliver performance and convenience.
Top Page Image Contents