90539499 01 EM100B.qxd 7/7/08 10:05 AM Page 26
05 DETERMINEBILLING MODE AND BILLING RATE
Determine Your Billing Rates and Time Slots
Now refer to your own electric bill. Find your
If applicable, add fees and taxes to each base rate to obtain accurate total billing rates, as shown in the example.
If your rates are in dollars per
Enter the Billing Rates and Time Slots from your electric bill in the table below.
The Power Monitor allows for two or three different
RECORD YOUR BILLING RATES AND TIME SLOTS HERE
OFF Peak Rate |
| ¢/kWh | |
|
|
|
|
06 PROGRAM DIGITAL DISPLAY - TIME, DAY,
TEMPERATURE, POWER FACTOR, BILLINGMODE
The prog/sync button on top of the Digital Display is used to enter
Program Mode and to enter data for each programming step.
If the Digital Display detects no activity for one minute while in Program Mode, it will automatically save your data and exit to Display Mode. Also, you can exit Program Mode at any point by holding prog/sync for three seconds.
The buttons change the value on the screen. To make the numbers change faster,
you can hold the button down continuously until you reach the desired number.
If you enter a wrong value and accidentally save it, you can exit Program Mode. Then go back into Program Mode and step through each entry until you get to the one you need to fix. Any data you’ve already entered will be saved.
Follow these steps to program the Digital Display with your Power Factor (which you recorded in section 03 Installing Your Meter Sensor), your Electric Bill information, and display preferences.
MID Peak Rate |
|
|
|
| ¢/kWh |
| Weekdays | ||||||
|
|
|
|
| |||||||||
|
|
|
|
| Weekends | ||||||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||
ON Peak Rate |
|
|
|
| ¢/kWh |
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BILLING SCHEDULE |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SLOT | START TIME |
|
| RATE TYPE | |||||||||
1 |
|
|
|
| AM |
|
| ON PEAK |
|
| OFF PEAK | ||
: |
|
|
|
| |||||||||
|
| PM |
|
| MID PEAK |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
STEP
Put Digital Display into Program mode
ACTION/PRESS
Hold three seconds
until you hear one beep.
DISPLAY
Beep!
2 | : |
|
|
| AM |
|
| ON PEAK |
|
| OFF PEAK |
|
|
| PM |
|
| MID PEAK |
|
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
| AM |
|
| ON PEAK |
|
| OFF PEAK |
: |
|
|
|
|
|
|
| ||||
|
|
| PM |
|
| MID PEAK |
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
4 |
|
|
|
| AM |
|
| ON PEAK |
|
| OFF PEAK |
: |
|
|
|
| |||||||
|
|
| PM |
|
| MID PEAK |
|
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
| AM |
|
| ON PEAK |
|
| OFF PEAK |
: |
|
|
|
|
|
|
| ||||
|
|
| PM |
|
| MID PEAK |
|
|
| ||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
|
|
| AM |
|
| ON PEAK |
|
| OFF PEAK |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
| PM |
|
| MID PEAK |
|
|
|
|
|
|
|
|
|
|
|
|
|
Go to Section 6, Program
Digital Display.
Set current time.
Set hours and AM/PM.
Set minutes.
Set clock for 12 Hr (regular time) or
24 Hr (military time).
Continue on the top of the next page.
26 |
|
|
|
| 27 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|