Chicago Electric 69275 owner manual Stand Parts List, Safety Setup Operation

Page 18

Main Parts List (continued, parts 101+)

SAFETY

SETUP

OPERATION

Part	Description	Size	Qty
101	Bolt	M6×20	2
102	Angle Pointer		1
103	O Type Ring	Ø6.7×1.8	1
104	Depth Lock Pin		1
105	Depth Lock		1
106	Bolt	M6×75	2
107	Front Limited Block		1
108	Locknut	M6	5
109	Bolt	M10×75	4
110	Spring Washer	10	4
111	Handle Asm.		1
112	Left Rail		1
113	Bolt Sleeve, B		4
114	Insert A		2
115	Insert B		2
116	Frame		1
117	Flat Washer	8	10
118	Cross Head Screw	ST4.2×35	5
119	Bolt	M8×40	2
120	Front Panel		1
121	Locknut	M8	7
122	Back Limited Block		1
123	Press Spring, A		1
124	Limited Bolt		1
125	Right Rail		1
126	Bolt	M8×65	8
127	Rubber Pad A		1
128	Rubber Pad B		2
129	Rubber Pad C		1
130	Rubber Pad I		1
131	Rubber Pad II		2
132	Rubber Pad III		1
133	Spring Washer	8	2
134	Bolt	M8×30	2
135	Side Working Table		1
136	Bearing Screw, A		3
137	C-clip	22	6

Part	Description	Size	Qty
138	Bearing	608-RS	9
139	Wheel A		3
140	Bearing Washer, A		2
141	Bolt Sleeve A		1
142	Eccentric Screw		3
143	Working Table		1
144	Wheel, B		3
145	Bearing Screw, C		1
146	Eccentric Screw, B		2
147	Bearing Washer, B		3
148	Pin Handle		1
149	Pin		1
150	Ball	Ø4	1
151	Press Spring, B		1
152	Particle Tray		1
153	Set Screw (Glued)	M6×8	1
154	Support Plate		1
155	Plate		1
156	Cross Head Bolt	M6×10	1
157	Miter Lock Lever		1
158	Miter Lock Screw		1
159	Miter Gauge Screw		1
160	Miter Gauge		1
161	Ball	Ø8	1
162	Press Spring, C		1
163	Gauge Lock Knob		1
164	Angle Plate		1
165	Clamp Plate		1
166	Chain Connector		1
167	Ring		2
168	Chain Asm.		1
169	Ring		1
170	Plug		1
171	Hose	Ø8	1
172	Pump		1
173	Water Tray		1

Stand Parts List

Note: Stand sold separately.

MAINTENANCE

Part	Description	Size	Qty
1a	Hex Bolt	M8×55	2
2a	Insert C		2
3a	Bolt	M8×20	2
4a	Front Support Leg Asm.		1
5a	Foot		2
6a	Flat Washer	8	4

Part	Description	Size	Qty
7a	Locknut	M8	2
8a	Rear Support Leg Asm.		1
9a	Flat Washer	12	2
10a	Wheel		2
11a	Flat Washer	10	2
12a	Locknut	M10	2

Page 18

For technical questions, please call 1-800-444-3353.

Item 69275

Image 18

Contents Industrial TILE/BRICK SAW Save this ManualTable of Contents General Tool Safety Warnings SafetySetup Operation Maintenance 110-120 V~ Grounded Tools Tools with Three Prong Plugs Grounding InstructionsGrounding Pin Tile Saw Safety Warnings Tile Saw Power Cord Drip Loop Extension Safety Setup OperationPower Cord Drip Loop Position of Tile SAWAdditional Tile SAW Safety Warnings Vibration Safety SpecificationsSetup Before Use FunctionsOperation Maintenance Installing the Water Tray Frame to the Leg StandInstalling Motor Head and Water Tray Frame To Prevent Serious Injury from Accidental OperationInstalling the Particle Tray Water Tray and Pump SetupSetup Operation Installing Blade Operating InstructionsInner Outer Flange Flange Spindle Nut Blade Depth Adjustment Miter AdjustmentBevel Adjustment Work Piece and Work Area Set UpFigure N Straight Cut Cleaning, Maintenance, and Lubrication Maintenance and ServicingTo Prevent Serious Injury from Tool Failure Troubleshooting Problem Possible Causes Likely SolutionsMain Parts List parts Parts Lists and DiagramStand Parts List Assembly Diagram 1a 2a 2a 4a 5a 6a 3a 7a10a 11a 12a For technical questions, please call Limited 90 Day Warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800