Craftsman 137.21194 operating instructions Tools Needed for Assembly, Supplied Not supplied

Page 12

TOOLS NEEDED FOR ASSEMBLY

Supplied	Not supplied
Blade Wrench	Adjustable Wrench	Phillips Screwdriver
Blade Wrench	Adjustable Wrench
	6mm Hex Wrench	Slotted Screwdriver

Combination Square

COMBINATION SQUARE MUST BE TRUE

Should not gap or overlap when square is ﬂipped over (see dotted ﬁgure).

	Draw light line on	Straight edge or a 3/4 in. board, this
	Draw light line on	edge must be perfectly straight.
	board along this edge.	edge must be perfectly straight.
	board along this edge.

Should not gap or overlap when square ﬂipped over (see dotted ﬁgure).

Image 12

Contents Operator’s Manual Sears, Roebuck and Co., Hoffman Estates, lL 60179 USATable of Contents WarrantyProduct Specifications MotorBlade Size Rotating TableSymbols ProhibitionSupport and Clamp Work Power Tool Safety General Safety Instructions Before Using this Power ToolAlways Wear EYE DANGER Compound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWPage Power Supply and Motor Specifications Motor Safety Protection ImportantDouble Insulated Guidelines for Extension Cords Minimum Gauge for Extension Cords AWGAccessories and Attachments Recommended AccessoriesAccessories Tools Needed for Assembly Supplied Not suppliedCombination Square Must be True Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Woodworking Terms Revolutions PER Minute RPMAssembly and Adjustments Installing the Support Bracket FIG. aInstalling the Miter Handle FIG. B Installing the Dust BAG FIG. CSAW Blade Wrench FIG. E Releasing Cutting Head FIG. GUnlocking the Slide Carriage FIG. F Removing and Installing the Table Insert FIG. H Mounting the Miter SAW FIG. I, JRemoving or Installing BladeInstalling Blade FIG. K, L, M Un-plug the miter saw before changing/installing the bladeLaser Guide FIG. N Laser BeamAvoid Direct EYE Contact Bevel Stop Adjustments FIG. O, P, Q Fig. O Bevel Pointer Adjustment Fig. PMiter Angle Adjustment FIG. R Miter Scale Indicator Adjustment FIG. RAdjusting Fence Squareness FIG. S Adjusting Cutting Depth FIG. T Fig. SAssembly and Adjustments Requirements and Safety Before Each USE Inspect Your SAWTroubleshooting Guide for adjustment if necessary OperationDress for Safety Plan Your WorkInspect Your Workpiece When SAW is Running Do not OVER-REACHNever cut freehand USE Extra Caution with Large or ODD Shaped WorkpiecesBody and Hand Position FIG. U Finishing a cutBefore freeing jammed material Basic SAW OperationsSliding Carriage System FIG. W Miter CUT FIGBefore Leaving the SAW Bevel CUT FIG. Y Compound CUT FIG. ZTo Slide Cut Wide Boards Fig. AA Cutting Bowed Material FIG. BBRough Cutting a Dado FIG. CC Fig. CC Bevel/Miter Settings Only When the Angle Between the Walls EqualsCutting Crown Molding FIG. GG, HH KEY Bevel Miter Type of CUT Setting Inside corner-Left sideInside corner-Right side Outside corner-Left sideCrown Molding Chart Maintenance MaintenanceReplacing Carbon Brushes FIG Lower Blade GuardDebris from entering eyes when Removing sawdust from unit SawdustWear proper eye protection to keep Lubrication FIG. JJ, KKTroubleshooting Guide EYE Protection Parts List Parts List for SAW SchematicSchematic 4 in. Compound Miter SAW Model noParts List for Motor Description Size QtySears Parts & Repair Service Center LE-FOYER MCSU-HOGAR R