Craftsman 137.21194 Laser Guide FIG. N, Laser Beam, Avoid Direct EYE Contact

Page 22

!WARNING

●To avoid injury, never use the saw without the cover plate secure in place. It keeps the arbor bolt from falling out if it accidentally loosens, and helps prevent the spinning blade from coming off the saw.

●Make sure the collars are clean and properly arranged. Lower the blade into the table and check for any contact with the metal base or the turn table.

THE LASER GUIDE (FIG. N)

1.To turn laser on, press on/off rocker switch (1) to “ON” position.

2.To turn off laser, press on/off rocker switch to “OFF” position.

Fig. N 1

THE LASER BEAM

!WARNING

For your own safety, never connect the plug to power source outlet until all the adjustment steps

are complete and you have read and understood the safety and operational instructions.

Your tool is equipped with the Laser Trac® cutting guide using Class II laser beam. The laser beam will enable you to preview the saw blade path on the stock to be cut before starting the miter saw. This laser guide is powered by the transformed alternating current supply directly through the power lead. The

saw must be connected to the power source and the laser on/off switch must be turned on for the laser line to show.

!WARNING

AVOID DIRECT EYE CONTACT

●Laser is radiated when laser guide is turned on. Avoid direct eye contact. Always un-plug the miter saw from power source before making any adjustments.

●Laser Warning Label: max output <1mW DIODE LASER:

630-670nm, Complies with 21CFR 1040.10 and 1040. 11. Class II laser product.

●NOTE: All the adjustments for the operation of this machine have been completed at the factory. Due to normal wear and use, some occasional readjustments may be necessary.

●CAUTION-Use of controls or adjustments or performance of procedures other than those speciﬁed herein may result in hazardous radiation exposure.

●CAUTION-The use of optical instruments with this product will increase eye hazard.

●Do not attempt to repair or disassemble the laser. If unqualiﬁed persons attempt to repair this laser product, serious injury may result. Any repair required on this laser product should be performed by authorized service center personnel.

22

Image 22

Contents Operator’s Manual Sears, Roebuck and Co., Hoffman Estates, lL 60179 USATable of Contents WarrantyBlade Size Product SpecificationsMotor Rotating TableProhibition SymbolsSupport and Clamp Work General Safety Instructions Before Using this Power Tool Power Tool SafetyAlways Wear EYE DANGER Compound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWPage Motor Safety Protection Important Power Supply and Motor SpecificationsDouble Insulated Guidelines for Extension Cords Minimum Gauge for Extension Cords AWGRecommended Accessories Accessories and AttachmentsAccessories Supplied Not supplied Tools Needed for AssemblyCombination Square Must be True Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Woodworking Terms Revolutions PER Minute RPMInstalling the Miter Handle FIG. B Assembly and AdjustmentsInstalling the Support Bracket FIG. a Installing the Dust BAG FIG. CReleasing Cutting Head FIG. G SAW Blade Wrench FIG. EUnlocking the Slide Carriage FIG. F Removing and Installing the Table Insert FIG. H Mounting the Miter SAW FIG. I, JRemoving or Installing BladeInstalling Blade FIG. K, L, M Un-plug the miter saw before changing/installing the bladeLaser Beam Laser Guide FIG. NAvoid Direct EYE Contact Bevel Stop Adjustments FIG. O, P, Q Fig. O Bevel Pointer Adjustment Fig. PMiter Scale Indicator Adjustment FIG. R Miter Angle Adjustment FIG. RAdjusting Fence Squareness FIG. S Adjusting Cutting Depth FIG. T Fig. STroubleshooting Guide for adjustment if necessary Assembly and AdjustmentsRequirements and Safety Before Each USE Inspect Your SAW OperationPlan Your Work Dress for SafetyInspect Your Workpiece Never cut freehand When SAW is RunningDo not OVER-REACH USE Extra Caution with Large or ODD Shaped WorkpiecesBefore freeing jammed material Body and Hand Position FIG. UFinishing a cut Basic SAW OperationsMiter CUT FIG Sliding Carriage System FIG. WBefore Leaving the SAW Bevel CUT FIG. Y Compound CUT FIG. ZCutting Bowed Material FIG. BB To Slide Cut Wide Boards Fig. AARough Cutting a Dado FIG. CC Fig. CC Only When the Angle Between the Walls Equals Bevel/Miter SettingsCutting Crown Molding FIG. GG, HH Inside corner-Right side KEY Bevel Miter Type of CUT SettingInside corner-Left side Outside corner-Left sideCrown Molding Chart Replacing Carbon Brushes FIG MaintenanceMaintenance Lower Blade GuardWear proper eye protection to keep Debris from entering eyes when Removing sawdust from unitSawdust Lubrication FIG. JJ, KKTroubleshooting Guide EYE Protection Parts List Parts List for SAW SchematicSchematic 4 in. Compound Miter SAW Model noParts List for Motor Description Size QtyLE-FOYER MC Sears Parts & Repair Service CenterSU-HOGAR R