Craftsman 137.21194 Product Specifications, Motor, Blade Size, Rotating Table, Cutting Capacity

Page 3

PRODUCT SPECIFICATIONS

MOTOR

 

Power Source

9Amp, 120V AC, 60Hz

Speed

5000 RPM (No load)

Brake

Electric

Double Insulated

Yes

BLADE SIZE

 

Diameter

7-1/4 in.

Arbor size

5/8 in.

ROTATING TABLE:

 

Diameter

9-1/32 in.

Miter Detent Stops

0, 15, 22.5, 31.6, 45º R & L

Bevel Positive Stops

0, 45º L

CUTTING CAPACITY:

 

Crosscut

2 in. x 8 in.

Miter 45° R & L

2 in. x 6 in.

Bevel 45º L

1-1/2 in. x 8 in.

45° Miter and 45° Bevel

1-1/2 in. x 6 in.

!WARNING

To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection.

This tool is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.

Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the tool.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Operator’s ManualWarranty Table of ContentsRotating Table Product SpecificationsMotor Blade SizeSymbols ProhibitionSupport and Clamp Work Power Tool Safety General Safety Instructions Before Using this Power ToolAlways Wear EYE DANGER Specific Safety Instructions for this Compound Miter SAW Compound Miter SAW SafetyPage Power Supply and Motor Specifications Motor Safety Protection ImportantDouble Insulated Minimum Gauge for Extension Cords AWG Guidelines for Extension CordsAccessories and Attachments Recommended AccessoriesAccessories Tools Needed for Assembly Supplied Not suppliedCombination Square Must be True Carton Contents Know Your Sliding Compound Miter SAW Glossary of Terms Revolutions PER Minute RPM Woodworking TermsInstalling the Dust BAG FIG. C Assembly and AdjustmentsInstalling the Support Bracket FIG. a Installing the Miter Handle FIG. BSAW Blade Wrench FIG. E Releasing Cutting Head FIG. GUnlocking the Slide Carriage FIG. F Mounting the Miter SAW FIG. I, J Removing and Installing the Table Insert FIG. HBlade Removing or InstallingUn-plug the miter saw before changing/installing the blade Installing Blade FIG. K, L, MLaser Guide FIG. N Laser BeamAvoid Direct EYE Contact Fig. O Bevel Pointer Adjustment Fig. P Bevel Stop Adjustments FIG. O, P, QMiter Angle Adjustment FIG. R Miter Scale Indicator Adjustment FIG. RAdjusting Fence Squareness FIG. S Fig. S Adjusting Cutting Depth FIG. TOperation Assembly and AdjustmentsRequirements and Safety Before Each USE Inspect Your SAW Troubleshooting Guide for adjustment if necessaryDress for Safety Plan Your WorkInspect Your Workpiece USE Extra Caution with Large or ODD Shaped Workpieces When SAW is RunningDo not OVER-REACH Never cut freehandBasic SAW Operations Body and Hand Position FIG. UFinishing a cut Before freeing jammed materialSliding Carriage System FIG. W Miter CUT FIGBefore Leaving the SAW Compound CUT FIG. Z Bevel CUT FIG. YTo Slide Cut Wide Boards Fig. AA Cutting Bowed Material FIG. BBRough Cutting a Dado FIG. CC Fig. CC Bevel/Miter Settings Only When the Angle Between the Walls EqualsCutting Crown Molding FIG. GG, HH Outside corner-Left side KEY Bevel Miter Type of CUT SettingInside corner-Left side Inside corner-Right sideCrown Molding Chart Lower Blade Guard MaintenanceMaintenance Replacing Carbon Brushes FIGLubrication FIG. JJ, KK Debris from entering eyes when Removing sawdust from unitSawdust Wear proper eye protection to keepTroubleshooting Guide EYE Protection Parts List for SAW Schematic Parts List4 in. Compound Miter SAW Model no SchematicDescription Size Qty Parts List for MotorSears Parts & Repair Service Center LE-FOYER MCSU-HOGAR R
Top Page Image Contents