Craftsman 315.27119 Important Information for Recharging HOT Batteries, Chargingbattery Pack

Page 12

_1, WARNING:Alwayswearsafetygogglesorsafety

glasseswithsideshieldswhenoperatingtools. Failuretodosocouldresultin objectsbeingthrown intoyoureyes,resultingin possibleseriousinjury.

CHARGINGBATTERY PACK

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until light on front of charger changes from red to green.

Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (cutting followed by recharging) for them to become fully charged.

TO CHARGE

Charge battery pack only with the charger provided.

Make sure power supply is normal house voltage, 120 volts, 60 Hz, AC only.

Connect charger to power supply.

Attach battery pack to charger by aligning raised ribs on battery pack with grooves in charger, then slide battery back onto charger. See Figure 9.

BAI"rERY

PACK

TO

REMOVE

CHARGER

IO

AI-rACH

GROOVES

Fig. 9

Red light should turn on. Red light indicates fast charging mode.

If red light is flashing, this indicates battery pack is deeply discharged or hot.

if battery pack is hot, red light should become steady after battery pack has cooled down.

If battery pack is deeply discharged, red light should

become steady after voltage has increased, normally within 60 minutes.

If after one hour red light is still flashing, this indicates a defective battery pack and should be replaced. Green light on indicates battery pack is fully charged and slow charging to maintain battery pack.

Yellow light on and red light flashing indicates defective battery pack. Return battery pack to your nearest Sears Repair Center for checking or replacing.

When your battery pack becomes fully charged, the red light will turn OFF and the green light will turn ON.

After normal usage, 1 hour of charging time is required to be fully charged. A minimum charge time of 1-1/2

hours is required to recharge a completely discharged tool.

The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature.

When the batteries become fully charged, unplug your charger from power supply and remove the battery pack.

LED FUNCTION OF CHARGER

LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK:

Red LED Lighted = Fast Charging Mode.

Green LED Lighted = Fully Charged And Slow Charging To Maintain Battery Pack.

Red LED Flashing = Hot Or Deeply Discharged

Battery Pack. Also Defective Battery Pack After 1 Hour.

Yellow LED Lighted and Red LED Flashing = Defective Battery Pack.

IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES

Under extreme continuous use, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 1 hour before attempt- ing to recharge. When the battery pack becomes dis- charged and is hot, this will cause the red light on your battery charger to flash. When battery pack cools down, red light will glow continuously indicating fast charging mode, 1 hour charge time. Once the battery pack cools

down, it will recharge battery pack in fast charging mode as normal.

Note: This situation only occurs when extreme continuous

use of your saw causes the batteries to become hot. It does not occur under normal circumstances. Refer to

"CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears repair center for

electrical check.

12

Image 12
Contents 2 in mm 18 Volts Professional Cordless Trim SAW Table of Contents Modelbattery Pack ChargerPage Additional Specific Safety Rules Never hold piece being cut in your hands orFire, or serious personal injury Symbols Name Desig NATION/EXP Lanation DefinitionsSwitch Product Specifications Trim SAWBattery Pack Know Your Trim SAWBladewrench 5 mm Hexkey Tomaintainbatterypack Batterypackshown Charger Mounting ChargerLED Function of Charger RED LightonBatterypack Fig To Assemble BladeBladewasher Bladescrew On the spindleBA,,ER, C To Remove BladeChargingbattery Pack Important Information for Recharging HOT BatteriesBAIrERY Pack RemoveSAW Blades GasolineBlade Guard System Correctbladedepthsetting = Bladeexposed Onebladetooth RightKickback Bladesettoo Deep BELOWTIlE Materialtobe CUTDepth of CUT Adjustment Starting a CUT To Adjust Blade DepthWrong To Help Maintain Control RememberBase Assembly Widthof Cutscale Blade To Cross CUT or RIP CUTTopviewofsawguideline Blade Guidenotch OfsawAlternative RIP Method BEVEL- IScale Lower BladeguardTo Adjust Positive 0 Bevel StopTo Pocket Hexnut Carpentersbevelstop SquareBattery Pack Removal and Preparation for Recycling BatteriesWarranty 2214 273O See Back page for Parts Ordering Instructions Parts List Key Part No. NumberDescription Quan DescriptionGet it fixed, at your home or ours SU-HOGAR sM
Related manuals
Manual 24 pages 19.67 Kb