Craftsman 315.273731 owner manual See Figures 12A 12C, Armviewedfrombelow, Armlockknob Armcap

Page 22

INSTALLING THE YOKE ASSEMBLY

See Figures 12A - 12C.

The yoke rides in the carriage below the arm and supports the motor, the blade guard, and the blade. Install the yoke assembly from the front of the arm.

Remove the carriage stop screw and Iockwasher from below the front of the arm with a 1/4 in. hex key. See Figure 12A.

ARMVIEWEDFROMBELOW

CARRIAGESTOPSCREW

1/4 in. HEXKEY Fig. 12A

Remove the arm cap screws and arm cap from the front of the arm with a phillips screwdriver. See Figure 12B

ARMLOCKKNOB

ARMCAP _

_ARM CAPSCREWS

Fig. 12B

Remove and discard the two motor setscrews in

the bottom of the motor. They are for shipping purposes only.

Using the elevating handwheel, raise the arm 3 inches and remove the packing material.

Lock the arm with the arm lock knob, located on top of the front of the arm, so the arm doesn't swing while you are mounting the yoke assembly.

Pick up the yoke assembly and carefully slip it onto the carriage track below the arm. Keep it parallel with the arm so bearings slide in smoothly. See Figure 12C.

FOR CLARITY,CARRIAGECOVERSANDCARRIAGELOCK

KNOBARE NOT SHOWNIN ILLUSTRATION

ARMLOCKKNOB

BEARINGS(4)

CARRIAGE

YOKE

CARRIAGEARM LOCKKNOB

CARRIAGECOVER Fig. 12C

Reinstall the carriage stop screw, the Iockwasher, arm cap, and arm cap screws. Tighten all screws securely.

,t_ WARNING: Once the yoke assembly is on the carriage track, reinstall the arm cap, the arm cap

screws, the carriage stop screw, and the Iockwasher. Do not risk serious injury or damage to the saw by failing to replace these parts.

Tighten the carriage lock knob, on the carriage cover on the left of the arm, to lock the yoke assembly in place.

I:RI_FT=_MRNRADIALSAW 315.273731

22

Image 22
Contents Radial ARM SAW Full TWO Year Warranty on Craftsman Tool Installing Yoke Assembly Removing Always Wear Safety Glasses with Side Safety Alert SymbolEquipment 5CRRFI.HRNRADIAL SAW315.273731 Do not USE a Person AS a Substitute 7IRRIq.HRH Radial SAW315.273731 Extension Cords Grounding PIN Coverofgrounded OutletboxSee Figures PAN Headscrew Motorcover Lift Motorcoverto ExposeswitchBladearbor Dado Cut Bench TOOLS, Visit Your Nearest Sears Retail Store SawAssembly Sawassemblyshownas PackedSwitch Bcde HIJPencil HEX KeysFramingsquare Yoke Know Your Radial SAWSee a MotorLockhandle See Figures 8A-8DMiterscale Armlockknob Yokepivotlatch RIP Scales Locklever MotorSpacer FEN Elevating HandwheelBladeguard DustguideANTI-KICKBACK Hexnut See Figures 9A 9CLong LEG See FigureElevating Shaft Handwheel Armviewedfrombelow See Figures 12A 12CArmlockknob Armcap Thumbscrew Blade Guard Blade Blade Arbor Mounttable Supports Usingthesehole LocationsTableflat Washersupport BladetoARM To Tighten Lockwheel Yoke AssemblyArmlockknob ARM Turncounterclock Armcapmotor YokelockBevel See Figures 17A -17CClampbolt LockleverSee Figures 19A 19D TubeColumntube Columnsupport Rotation AdjustmentCAP Screws Carriagebearing Adjusting the Carriage BearingsSee Figures 20A and 20B Graspand HoldTablesupport Elevating Handwheel Armlock Knob Bevel Locklever BladewrenchAT Back RightsideSee Figures 22A 22C Phillipsscrewdriver On PAN Headscrew Setscrew Installing Rear TABLE, Spacer TABLE, FENCE, and ClampsLeveling the Front Table See Figures 24A 24CSupport Thumbscrew Clamp Bracket Squarenut Clampshown AssembledRectangle Loosen3KPAWLS See Figures 26A 26CKnob Rivingknifeontop of Fence TOO Farleftof BladeRipscale Indicator Carriage Cover Speednut Installing RIP Scale IndicatorsSpring Carriage Screws Edge Miterindicatorarm LockknobAligning the ARM for Cross Cuts Linealongthis EdgeSee Figures 29A 29D Bladesquareto Table Noadjustmentneeded Framing Square GAPAligning Blade to Table AT 0 Bevel Armlockknob Bevel Indexcap Lock LeverSee Figures 30A 30C No Adjustmentneeded FramingSquaring Blade to Fence ARM LockknobParalleling Blade to Table Noadjustment NeededAdjustment GAP Needed See Figures 31A-31CSee Figures 32A 32B Aligning the RIP Scale IndicatorsYokepivot Latch Barrel Fitting Installing Control CUT DeviceSocket Cross Cuts Basic Operation of the Radial ARM SAWTypes of Cuts RIP CutsSwitchon Switchoff Switch and Switch KEYInsertswitchkey Causes of KickbackPushblocks Cutting AidsPushsticks FeatherboardsMaking a Cross CUT TableclampsArmmiterscale Lockknob Yoke Pivot Latch Lock Handle Bladeguard Bevel Indicator Ercut LockleverMaking a Miter CUT Carriage YokelockBeveledcut ARM Lockknob Making a Bevel CUTRiving Knife Yokelock Handle Miterscale SwitchyokelockMaking a Compound Cross CUT Armpivot Latch LockRiP CUT Hazards and Precautions See Figure Review the Hazards and Precautions Making a RIP CUTCutting Long Workpieces Making Other CutsSee Figures 47 SupportlongworkpiecesControlCut Settings NON-THROUGH CutsGeneral Maintenance MOTOR/ELECTRICALProblem Assembly section Carriage Assembly in AssemDures in Adjustment See Adjusting ColumnProblem Causesolution See Adjusting the Column Tube in Assembly sectionRemove and clean tables 57CIIFTSMRRADIALSAW315.273731 Figure a See Figures F and G Description Parts List for Figure aKEY Part NO. Number QuanCraftsman Radial ARM SAW- Model no See Figure CParts List for Figure B KEY Part NO. NumberFigure C Parts List for Figure C KEY Part Number27--+---17 Parts List for Figure D Figure E Parts List for Figure E KEY Part NO.NUMBERFigure F See Figure GParts List for Figure F 69IRRFTSMRN RADIALSAW315.273731See Figure F See Figure HParts List for Figure G NumberFigure H Parts List for Figure H Craftsman Radial ARM SAW- Model no1725 1824 KEY Part Description Parts List for FigureDescription Quan Figure J Parts List for Figure J Figure K Parts List for Figure K Service and Repair Parts Call