Craftsman 315.273731 owner manual General Maintenance, Motor/Electrical

Page 52

GENERAL MAINTENANCE

,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other

part may create a hazard or cause product damage.

,_ WARNING: To prevent accidental starting that could cause possible serious personal injury, turn

off the saw with the switch on the arm, remove

the switch key, and unplug the saw before working on the radial saw.

•Remove sawdust from the work area, including inside the blade cover, frequently.

•Remove sawdust from and clean the blade guards frequently.

•Clean plastic parts with a soft damp cloth. Do not use any strong solvents.

,_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating

oils, etc. contact plastic parts. They contain chemicals that can damage, weaken or destroy plastic.

•Check teeth of anti-kickback pawls; sharpen with file if needed.

•Regularly check all nuts, bolts, screws, and cables for tightness and condition.

MOTOR/ELECTRICAL

•Frequently vacuum or blow out any sawdust from the work areas.

,_ WARNING: If the power cords are worn, cut, or damaged in any way, have them replaced

immediately by a qualified service technician at a Sears store or repair center. Failure to do so could result in serious personal injury.

_ WARNING: To avoid fire or electrocution, reassemble electric parts only with identical

Craftsman replacement parts. Reassemble exactly as originally assembled.

rRRFT,_MRN'RADIALSAW 315.273731

52

Image 52

Contents Radial ARM SAW Full TWO Year Warranty on Craftsman Tool Installing Yoke Assembly Removing Always Wear Safety Glasses with Side Safety Alert SymbolEquipment 5CRRFI.HRNRADIAL SAW315.273731 Do not USE a Person AS a Substitute 7IRRIq.HRH Radial SAW315.273731 Extension Cords Grounding PIN Coverofgrounded OutletboxSee Figures PAN Headscrew Motorcover Lift Motorcoverto ExposeswitchBladearbor Dado Cut Bench TOOLS, Visit Your Nearest Sears Retail Store SawAssembly Sawassemblyshownas PackedSwitch Bcde HIJPencil HEX KeysFramingsquare Know Your Radial SAW See aYoke MotorSee Figures 8A-8D Miterscale Armlockknob Yokepivotlatch RIP ScalesLockhandle Locklever MotorSpacer FEN Elevating HandwheelBladeguard DustguideANTI-KICKBACK Hexnut See Figures 9A 9CLong LEG See FigureElevating Shaft Handwheel Armviewedfrombelow See Figures 12A 12CArmlockknob Armcap Blade Arbor Mounttable Supports Usingthesehole Locations TableflatThumbscrew Blade Guard Blade Washersupport BladetoYoke Assembly Armlockknob ARM TurncounterclockARM To Tighten Lockwheel Armcapmotor YokelockSee Figures 17A -17C ClampboltBevel LockleverSee Figures 19A 19D TubeColumntube Columnsupport Rotation AdjustmentCAP Screws Adjusting the Carriage Bearings See Figures 20A and 20BCarriagebearing Graspand HoldArmlock Knob Bevel Locklever Bladewrench AT BackTablesupport Elevating Handwheel RightsideSee Figures 22A 22C Installing Rear TABLE, Spacer TABLE, FENCE, and Clamps Leveling the Front TablePhillipsscrewdriver On PAN Headscrew Setscrew See Figures 24A 24CThumbscrew Clamp Bracket Squarenut Clampshown Assembled RectangleSupport LoosenSee Figures 26A 26C Knob3KPAWLS Rivingknifeontop of Fence TOO Farleftof BladeRipscale Indicator Carriage Cover Speednut Installing RIP Scale IndicatorsSpring Carriage Screws Miterindicatorarm Lockknob Aligning the ARM for Cross CutsEdge Linealongthis EdgeBladesquareto Table Noadjustmentneeded Framing Square GAP Aligning Blade to Table AT 0 BevelSee Figures 29A 29D Armlockknob Bevel Indexcap Lock LeverNo Adjustmentneeded Framing Squaring Blade to FenceSee Figures 30A 30C ARM LockknobNoadjustment Needed Adjustment GAP NeededParalleling Blade to Table See Figures 31A-31CSee Figures 32A 32B Aligning the RIP Scale IndicatorsYokepivot Latch Barrel Fitting Installing Control CUT DeviceSocket Basic Operation of the Radial ARM SAW Types of CutsCross Cuts RIP CutsSwitch and Switch KEY InsertswitchkeySwitchon Switchoff Causes of KickbackCutting Aids PushsticksPushblocks FeatherboardsMaking a Cross CUT TableclampsLock Handle Bladeguard Bevel Indicator Ercut Locklever Making a Miter CUTArmmiterscale Lockknob Yoke Pivot Latch Carriage YokelockBeveledcut ARM Lockknob Making a Bevel CUTRiving Knife Yokelock Handle Switchyokelock Making a Compound Cross CUTMiterscale Armpivot Latch LockRiP CUT Hazards and Precautions See Figure Review the Hazards and Precautions Making a RIP CUTMaking Other Cuts See Figures 47Cutting Long Workpieces SupportlongworkpiecesControlCut Settings NON-THROUGH CutsGeneral Maintenance MOTOR/ELECTRICALProblem Carriage Assembly in Assem Dures in AdjustmentAssembly section See Adjusting ColumnProblem Causesolution See Adjusting the Column Tube in Assembly sectionRemove and clean tables 57CIIFTSMRRADIALSAW315.273731 Figure a See Figures F and G Parts List for Figure a KEY Part NO. NumberDescription QuanCraftsman Radial ARM SAW- Model no See Figure CParts List for Figure B KEY Part NO. NumberFigure C Parts List for Figure C KEY Part Number27--+---17 Parts List for Figure D Figure E Parts List for Figure E KEY Part NO.NUMBERFigure F See Figure GParts List for Figure F 69IRRFTSMRN RADIALSAW315.273731See Figure F See Figure HParts List for Figure G NumberFigure H Parts List for Figure H Craftsman Radial ARM SAW- Model no1725 1824 KEY Part Description Parts List for FigureDescription Quan Figure J Parts List for Figure J Figure K Parts List for Figure K Service and Repair Parts Call