Craftsman 315.273731 owner manual Remove and clean tables

Page 56

PROBLEM

CAUSE

SOLUTION

Miter or cross cuts are not true.

Wood edges away from fence when ripping.

Depth of cut varies from one end of wood to the other.

Riving knife strikes wood during a cut.

1.Scale pointer is not correct.

2.Column is out of alignment.

3.Carriage is misaligned.

4.Yoke is loose on carriage.

5.Arm is out of alignment.

6.Sawdust has collected between tables.

7.Table top is not parallel to the arm.

8.Fence/tables are not straight.

1.Blade is not parallel with fence.

2.Arm is not perpendicular to fence.

3.Riving knife needs adjustment.

1.Table is not parallel to arm.

2.Column tube is loose in column support.

3.Arm is loose or misaligned.

1.Riving knife not aligned with blade,

1.Reset the pointer at the top rear of arm.

2.See Adjusting the Column Tube in Assembly section.

3.See Setting the Arm Lock Wheel in the Assembly section.

4.See Setting the Yoke Clamp procedure in Assembly section.

5.See Aligning Arm for Cross Cuts in Adjustments section.

6.Remove and clean tables.

7.See Leveling Table Supports and Leveling the Front Table in the Assembly section.

8.Check with square; sand or replace.

1.See Squaring the Blade to the Fence procedure in the Adjust- ments section.

2.See Aligning the Arm for Cross Cuts procedure in the Adjust- ments section.

3.See Aligning the Riving Knife to the Blade procedure in the Adjustments section.

1.See Leveling Table Supports and Leveling the Front Table in the Assembly section.

2.See Adjusting the Column Tube in Assembly section.

3.See Setting the Arm Lock Wheel in the Assembly section.

1.See Aligning the Riving Knife to the Blade procedure in the Adjustments section.

rRRFT,_MRN° RADIALSAW 315.273731

56

Image 56

Contents Radial ARM SAW Full TWO Year Warranty on Craftsman Tool Installing Yoke Assembly Removing Equipment Safety Alert SymbolAlways Wear Safety Glasses with Side 5CRRFI.HRNRADIAL SAW315.273731 Do not USE a Person AS a Substitute 7IRRIq.HRH Radial SAW315.273731 Extension Cords Grounding PIN Coverofgrounded OutletboxBladearbor PAN Headscrew Motorcover Lift Motorcoverto ExposeswitchSee Figures Dado Cut Bench TOOLS, Visit Your Nearest Sears Retail Store SawAssembly Sawassemblyshownas PackedSwitch Bcde HIJFramingsquare HEX KeysPencil Know Your Radial SAW See aYoke MotorSee Figures 8A-8D Miterscale Armlockknob Yokepivotlatch RIP ScalesLockhandle Locklever MotorSpacer FEN Elevating HandwheelANTI-KICKBACK DustguideBladeguard Long See Figures 9A 9CHexnut Elevating Shaft Handwheel See FigureLEG Armlockknob Armcap See Figures 12A 12CArmviewedfrombelow Blade Arbor Mounttable Supports Usingthesehole Locations TableflatThumbscrew Blade Guard Blade Washersupport BladetoYoke Assembly Armlockknob ARM TurncounterclockARM To Tighten Lockwheel Armcapmotor YokelockSee Figures 17A -17C ClampboltBevel LockleverSee Figures 19A 19D TubeCAP Screws Rotation AdjustmentColumntube Columnsupport Adjusting the Carriage Bearings See Figures 20A and 20BCarriagebearing Graspand HoldArmlock Knob Bevel Locklever Bladewrench AT BackTablesupport Elevating Handwheel RightsideSee Figures 22A 22C Installing Rear TABLE, Spacer TABLE, FENCE, and Clamps Leveling the Front TablePhillipsscrewdriver On PAN Headscrew Setscrew See Figures 24A 24CThumbscrew Clamp Bracket Squarenut Clampshown Assembled RectangleSupport LoosenSee Figures 26A 26C Knob3KPAWLS Rivingknifeontop of Fence TOO Farleftof BladeSpring Carriage Screws Installing RIP Scale IndicatorsRipscale Indicator Carriage Cover Speednut Miterindicatorarm Lockknob Aligning the ARM for Cross CutsEdge Linealongthis EdgeBladesquareto Table Noadjustmentneeded Framing Square GAP Aligning Blade to Table AT 0 BevelSee Figures 29A 29D Armlockknob Bevel Indexcap Lock LeverNo Adjustmentneeded Framing Squaring Blade to FenceSee Figures 30A 30C ARM LockknobNoadjustment Needed Adjustment GAP NeededParalleling Blade to Table See Figures 31A-31CYokepivot Latch Aligning the RIP Scale IndicatorsSee Figures 32A 32B Socket Installing Control CUT DeviceBarrel Fitting Basic Operation of the Radial ARM SAW Types of CutsCross Cuts RIP CutsSwitch and Switch KEY InsertswitchkeySwitchon Switchoff Causes of KickbackCutting Aids PushsticksPushblocks FeatherboardsMaking a Cross CUT TableclampsLock Handle Bladeguard Bevel Indicator Ercut Locklever Making a Miter CUTArmmiterscale Lockknob Yoke Pivot Latch Carriage YokelockRiving Knife Yokelock Handle Making a Bevel CUTBeveledcut ARM Lockknob Switchyokelock Making a Compound Cross CUTMiterscale Armpivot Latch LockRiP CUT Hazards and Precautions See Figure Review the Hazards and Precautions Making a RIP CUTMaking Other Cuts See Figures 47Cutting Long Workpieces SupportlongworkpiecesControlCut Settings NON-THROUGH CutsGeneral Maintenance MOTOR/ELECTRICALProblem Carriage Assembly in Assem Dures in AdjustmentAssembly section See Adjusting ColumnProblem Causesolution See Adjusting the Column Tube in Assembly sectionRemove and clean tables 57CIIFTSMRRADIALSAW315.273731 Figure a See Figures F and G Parts List for Figure a KEY Part NO. NumberDescription QuanCraftsman Radial ARM SAW- Model no See Figure CParts List for Figure B KEY Part NO. NumberFigure C Parts List for Figure C KEY Part Number27--+---17 Parts List for Figure D Figure E Parts List for Figure E KEY Part NO.NUMBERFigure F See Figure GParts List for Figure F 69IRRFTSMRN RADIALSAW315.273731See Figure F See Figure HParts List for Figure G NumberFigure H Parts List for Figure H Craftsman Radial ARM SAW- Model no1725 1824 Description Quan Parts List for FigureKEY Part Description Figure J Parts List for Figure J Figure K Parts List for Figure K Service and Repair Parts Call