Craftsman 137.24884 operating instructions RiPFENCEiNDiCATORADJUSTMENTFIG.Q, Blade Tilting Pointer

Page 15

RiPFENCEiNDiCATORADJUSTMENT(FIG.Q)

1_Theripfenceindicator(6)pointstothemeasurement scale.Thescaleshowsthedistancefromthesideof thefencetonearestsideoftheblade.

2_ Measuretheactualdistancewitha rule.if there isadifferencebetweenthemeasurementandthe

indicator, adjust the indicator (6)_

3_ Loosen the screw (7) and slide the indicator to the correct measurement on the scale. Tighten the screw and remeasure with the rule.

IA WARNINGn

To avoid injury from an accidental start, make sure the switch is in the OFF position end the plug is not connected to the power source outtet.

ADJUSTING THE 90° (0°) AND 45 ° POSiTiVE STOPS (FIG. R, S, T}

Your saw has positive stops that will quickly position the saw blade at 90 ° (0°) to the taNe. Make adjustments only if necessary.

O0° (0°) Stop

1.Disconnect the saw from the power source.

2.Turn the blade elevation handwheel and raise the blade to the maximum elevation.

3.Loosen the blade bevel lock knob (1) and move the blade to the maximum vertical position, then tighten the lock knob (1).

4.Place a combination square on the table and against the blade (2) to determine if the blade is 90° (0°) to

the table. (Fig. S)

5.If the blade is not 90° (0°) to the table, loosen the two set screws (4), located on the collar (5) underneath the table saw (Fig. T) with the hex key and back off the collar.

6.Loosen the bevel lock knob, turn the blade tilting handwheel to move the blade until it is 90° (0°) to the

table and tighten the bevel lock knob.

7.Adjust the collar (5) so it contacts the bracket (3) when the blade is 90° (0°) to the table. Tighten the

two set screws (4) (Fig.T).

Fig. R

Fig. S

9o°(0o)

45 °

45° Stop

1.With the blade in the upright 90° (0°) position, loosen the bevel lock knob and move the blade to the maximum bevel angle.

2.Place the combination square on the table as shown in Fig. S to check if the blade is 45° to the table.

3.If the blade is not 45 ° to the table, loosen the two set screws (4), located on the collar (5) underneath the table saw, (Fig. T) with the hex key, and back off the collar.

4.Loosen the bJade bevel lock knob, turn the blade tilting handwheel to move the blade until it is 45° to the table and tighten the blade beve! lock knob.

5.Adjust the collar (5) so it contacts the bracket (3) when the blade is 45° to the table. Tighten the two set screws.

BLADE TILTING POINTER

1.When the blade is positioned at 90° (0°), adjust the blade tilt pointer to read 0° on the scale.

2.Loosen the mounting screw, position pointer over 0° and tighten the screw.

NOTE: Make a trial cut on scrap wood before making critical cuts. Measure for exactness.

Fig. T

4

5

3

o

3 4 5

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Operators Manual 10 in. Table SAW Model NoYES ONE-YEAR Full Warranty on Craftsman ToolSection SAWLa,WARNINGn USE only Recommended AccessoriesPage Cauton Event of a Malfunction orIA WARNINGn Description QuantityStand Abcd Mopq Rsuvwx BladeGuard RESIN= Astickysapthathashardened ARBOR=Theshaftonwhichthebladeordadois MountedBLADEELEVATIONHANDWHEEL= Raisesand lowerstheblade DUSTPORT= Holein backofsawbaseforattachment ofvacuumhoseASSEMBLESTANDFIG.A Assemblerearframesectionin exactlythesame mannerAssemble Table SAW to Stand FIG. B Fastenthesawtotheworksurface MOUNTSAWONWORKSURFACEFIG.CThesurfaceofthetablewherethesawistobe Drill3/8in.holeintothemountingsurfaceWARNmN¢ IAWARNINGnInstalling Table Side EXTENS!ONS FIG. N BLADEGUARDASSEMBLYFIG.K, L, MRIP Fence Adjustment FIG. Q Adjusting Rear Table ExtensionBlade Tilting Pointer RiPFENCEiNDiCATORADJUSTMENTFIG.QBladeparalleltothemitergaugegroove FIG.U,V IA waRninGTilting the Blade FIG. W ON/OFF Switch FIGUsing the Table Extension FIG. Y, Z Raise the Blade FIG. WLa,WARNING IAwAR.I.GI REVELRiPPiNG ThiscutisthesameasrippingexceptthebladebevelCrosscutting 90 Miter Angle FIG. CO Auxiuary Fence FIG. H Using Wood Facing on the RIP Fence FIG. HNCOMPOUNDMITERCROSSCUTTINGFIG.FF ~45BLADE Bevel & 00~45 Miter AngleFig.JJ Attachauxiliaryfenceto ripfencewithtwoCclamps. Fig.ddBlade RAISmNG and TmLTmNGMECHANmSM FIGo LL IA Warn NenIAWARNmNGn Symptom Possible Causes Corrective ACT!ONWAR.I.G Parts List for SAW SchematicSchematic for SAW SAW Model Parts List and Schematic for StandParts List and Schematic for Motor Push Stick Construction Page SU-HOGAR LE-FOYER

137.24884 specifications

The Craftsman 137.24884 is a reliable and robust table saw that is ideal for both amateur woodworkers and seasoned professionals. This versatile piece of equipment combines performance, durability, and user-friendly features to cater to a variety of woodworking projects, making it a popular choice in workshops.

One of the most notable features of the Craftsman 137.24884 is its powerful 15-amp motor, which delivers ample cutting power to handle hardwoods, softwoods, and various other materials. The table saw boasts a 10-inch blade that allows for precision cuts and can easily handle rip cuts, crosscuts, and bevel cuts. With a maximum rip capacity of 30 inches, users can tackle larger workpieces with ease, enhancing productivity.

The saw's stability is further complemented by its sturdy cast iron table, which provides a flat and smooth surface for accurate cuts. This enhances the overall performance by minimizing vibrations during operation, ensuring that cuts remain true and consistent. Additionally, the adjustable fence system locks securely in place, allowing users to make precise adjustments and achieve repeatable results.

Safety is a key consideration in the design of the Craftsman 137.24884. It comes equipped with a blade guard and anti-kickback pawls, providing an added layer of protection for users. A push stick is also included, promoting safe operation when handling smaller workpieces.

In terms of portability, the saw features a lightweight design complemented by wheels that facilitate easy movement around the workshop or job site. This portability does not compromise its overall strength and stability, which are crucial for accurate table sawing.

Moreover, the Craftsman 137.24884 incorporates easy-to-access controls, allowing users to quickly change blades or adjust settings. Its onboard storage system keeps essential accessories organized and within reach, enhancing the overall user experience.

In summary, the Craftsman 137.24884 table saw combines powerful performance, precision engineering, and essential safety features, making it an excellent investment for anyone interested in woodworking. This model's durable construction and user-friendly design set it apart as a reliable tool that can tackle both small and large projects effectively. Whether constructing furniture or handling renovations, the Craftsman 137.24884 is a solid choice for precision cut woodworking.
Top Page Image Contents