Craftsman 137.24884 operating instructions IA waRninG, Bladeparalleltothemitergaugegroove FIG.U,V

Page 16

BLADEPARALLELTOTHEMITERGAUGEGROOVE (FIG.U,V)

I_WARNiNG

This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

IA waRninG

To prevent personal injury:

o Always disconnect plug from the power source when making any adjustments.

o This adjustment must be correct or kickback could result in a serious injury and accurate cuts can not be made.

1.Remove the safety switch key and unplug the saw.

2.Remove the blade guard for this procedure but reinstal! and realign after adjustment.

3.Raise the blade to the highest position and set at the 0° angle (90° straight up).

4.Select and mark, with a felt tip maker, a blade tooth

having a "right set" and rotate the blade so the marked tooth is Y2in. above the table.

5.Place the combination square base (1) into the right side miter gauge groove (2). (Fig. U)

6.Adjust the rule so it touches the front marked tooth and lock ruler so it holds its position in the square assembly.

7.Rotate the blade bringing the marked tooth to the rear and about 1/2in. above the blade.

8.Carefully slide the combination square to the rear until the ruler touches the marked tooth.

9.If the ruler touches the marked tooth at the front and rear position, no adjustment is needed at this time. If not or the base of the rule is no longer parallel with the edge of the miter gauge groove, perform adjustment procedure described in next section.

Fig. U

2

1

Additional blade adjustments (Fig. V)

NOTE: The adjusting nuts are 8ram.

The adjusting mechanism is located above the blade height adjusting hand whee! under the tabletop. If the front and rear measurements are not the same.

if the blade is partial to right side:

1.Loosen the two nuts (1) and turn the left screw (2) counterclockwise, then adjust the right side screw (3) clockwise.

2.Remeasure, as described in steps 4 to 9 in the prior section.

3.When alignment is achieved, turn the left screw (2) unti! it touches the pivot rod (4) then tighten both nuts (1)_

ffthe blade is partial to left side:

1.Loosen the two nuts (1) and turn the right screw (3) counterclockwise, then adjust the left side screw (2) clockwise.

2.Remeasure, as described in steps 4 to 9 in the prior section.

3.When alignment is achieved, turn the right screw (3) unti! it touches the pivot rod (4) then tighten both nuts (1).

Fig, V

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operators Manual 10 in. Table SAW Model No Sears, Roebuck and Co., Hoffman Estates, IL 60179 USAONE-YEAR Full Warranty on Craftsman Tool SectionSAW YESUSE only Recommended Accessories La,WARNINGnPage Event of a Malfunction or CautonDescription Quantity IA WARNINGnStand Abcd Mopq Rsuvwx BladeGuard ARBOR=Theshaftonwhichthebladeordadois Mounted BLADEELEVATIONHANDWHEEL= Raisesand lowersthebladeDUSTPORT= Holein backofsawbaseforattachment ofvacuumhose RESIN= AstickysapthathashardenedAssemblerearframesectionin exactlythesame manner ASSEMBLESTANDFIG.AAssemble Table SAW to Stand FIG. B MOUNTSAWONWORKSURFACEFIG.C ThesurfaceofthetablewherethesawistobeDrill3/8in.holeintothemountingsurface FastenthesawtotheworksurfaceIAWARNINGn WARNmN¢BLADEGUARDASSEMBLYFIG.K, L, M Installing Table Side EXTENS!ONS FIG. NAdjusting Rear Table Extension RIP Fence Adjustment FIG. QRiPFENCEiNDiCATORADJUSTMENTFIG.Q Blade Tilting PointerIA waRninG Bladeparalleltothemitergaugegroove FIG.U,VON/OFF Switch FIG Using the Table Extension FIG. Y, ZRaise the Blade FIG. W Tilting the Blade FIG. WLa,WARNING REVELRiPPiNG Thiscutisthesameasrippingexceptthebladebevel IAwAR.I.GICrosscutting 90 Miter Angle FIG. CO Using Wood Facing on the RIP Fence FIG. HN COMPOUNDMITERCROSSCUTTINGFIG.FF~45BLADE Bevel & 00~45 Miter Angle Auxiuary Fence FIG. HAttachauxiliaryfenceto ripfencewithtwoCclamps. Fig.dd Fig.JJIA Warn Nen Blade RAISmNG and TmLTmNGMECHANmSM FIGo LLSymptom Possible Causes Corrective ACT!ON IAWARNmNGnParts List for SAW Schematic WAR.I.GSchematic for SAW Parts List and Schematic for Stand SAW ModelParts List and Schematic for Motor Push Stick Construction Page LE-FOYER SU-HOGAR

137.24884 specifications

The Craftsman 137.24884 is a reliable and robust table saw that is ideal for both amateur woodworkers and seasoned professionals. This versatile piece of equipment combines performance, durability, and user-friendly features to cater to a variety of woodworking projects, making it a popular choice in workshops.

One of the most notable features of the Craftsman 137.24884 is its powerful 15-amp motor, which delivers ample cutting power to handle hardwoods, softwoods, and various other materials. The table saw boasts a 10-inch blade that allows for precision cuts and can easily handle rip cuts, crosscuts, and bevel cuts. With a maximum rip capacity of 30 inches, users can tackle larger workpieces with ease, enhancing productivity.

The saw's stability is further complemented by its sturdy cast iron table, which provides a flat and smooth surface for accurate cuts. This enhances the overall performance by minimizing vibrations during operation, ensuring that cuts remain true and consistent. Additionally, the adjustable fence system locks securely in place, allowing users to make precise adjustments and achieve repeatable results.

Safety is a key consideration in the design of the Craftsman 137.24884. It comes equipped with a blade guard and anti-kickback pawls, providing an added layer of protection for users. A push stick is also included, promoting safe operation when handling smaller workpieces.

In terms of portability, the saw features a lightweight design complemented by wheels that facilitate easy movement around the workshop or job site. This portability does not compromise its overall strength and stability, which are crucial for accurate table sawing.

Moreover, the Craftsman 137.24884 incorporates easy-to-access controls, allowing users to quickly change blades or adjust settings. Its onboard storage system keeps essential accessories organized and within reach, enhancing the overall user experience.

In summary, the Craftsman 137.24884 table saw combines powerful performance, precision engineering, and essential safety features, making it an excellent investment for anyone interested in woodworking. This model's durable construction and user-friendly design set it apart as a reliable tool that can tackle both small and large projects effectively. Whether constructing furniture or handling renovations, the Craftsman 137.24884 is a solid choice for precision cut woodworking.
Top Page Image Contents