Craftsman 137.24884 operating instructions IA Warn Nen, Blade RAISmNG and TmLTmNGMECHANmSM FIGo LL

Page 22

GENERAL MAINTENANCE

IA WARNINGn

For your own safety, turn the switch OFF and remove the switch kay. Remove the plug from the power source outlet before maintaining or lubricating your saw.

1.Clean out al! sawdust that has accumulated inside the saw cabinet and the motor.

2.Polish the saw table with an automotive wax to keep it clean and to make it easier to slide the work piece.

3.Clean cutting blades with pitch and gum remover.

4.A worn, cut, or damaged power cord should be replaced immediately.

IA WARN Nen

All electrical or mechanical repairs should be attempted only by a trained repair technician. Contact the nearest Seers Service Center for service. Use only identical replacement parts. Any other parts may create a hazard.

5.Use liquid dish washing detergent and water to clean al! plastic part&

NOTE: Certain cleaning chemicals can damage plastic parts.

6.Avoid use of the following cleaning chemicals or solvents, ammonia and household detergents containing ammonia_

BLADE RAISmNG AND TmLTmNGMECHANmSM

(FIGo LL)

After each five hours of operation, the blade raising mechanism and tilting mechanism should be checked for looseness, binding, or other abnormalities. With the saw dis-connected from the power source, turn the saw upside down and alternately pull upward and downward on the motor unit. Observe any movement of the motor mounting mechanism. Looseness or play in the blade raising screw (1) should be adjusted as follows:

1.Using a wrench, loosen nut (2).

2.Adjust nut (3) until it is finger=tight against the bracket (4), and then back off the nut (3) 1/6 turn.

3.Tighten nut (2) with the wrench, while holding nut (3) in place. Maximum allowable play of screw rod (1) is 0.16 in. (4 mm).

Fig. LL

2

1

5

Place a small amount of dry lubricant on height regulating bolt (1). This must be kept clean and free of sawdust, gum, pitch, and other contaminants for smooth operation.

If excessive looseness is observed in any parts of the blade raising mechanism or tilting mechanism, take the complete unit to a Sears Service Center.

LUBRICATmON

All motor bearings are permanently lubricated at the factory and require no additional lubrication.

On all mechanical parts of your table saw where a pivot or threaded rod are present, lubricate using graphite or silicone. These dry lubricants wi!! not hold sawdust as would oil or grease.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operators Manual 10 in. Table SAW Model No Sears, Roebuck and Co., Hoffman Estates, IL 60179 USASAW ONE-YEAR Full Warranty on Craftsman ToolSection YESUSE only Recommended Accessories La,WARNINGnPage Event of a Malfunction or CautonDescription Quantity IA WARNINGnStand Abcd Mopq Rsuvwx BladeGuard DUSTPORT= Holein backofsawbaseforattachment ofvacuumhose ARBOR=Theshaftonwhichthebladeordadois MountedBLADEELEVATIONHANDWHEEL= Raisesand lowerstheblade RESIN= AstickysapthathashardenedAssemblerearframesectionin exactlythesame manner ASSEMBLESTANDFIG.AAssemble Table SAW to Stand FIG. B Drill3/8in.holeintothemountingsurface MOUNTSAWONWORKSURFACEFIG.CThesurfaceofthetablewherethesawistobe FastenthesawtotheworksurfaceIAWARNINGn WARNmN¢BLADEGUARDASSEMBLYFIG.K, L, M Installing Table Side EXTENS!ONS FIG. NAdjusting Rear Table Extension RIP Fence Adjustment FIG. QRiPFENCEiNDiCATORADJUSTMENTFIG.Q Blade Tilting PointerIA waRninG Bladeparalleltothemitergaugegroove FIG.U,VRaise the Blade FIG. W ON/OFF Switch FIGUsing the Table Extension FIG. Y, Z Tilting the Blade FIG. WLa,WARNING REVELRiPPiNG Thiscutisthesameasrippingexceptthebladebevel IAwAR.I.GICrosscutting 90 Miter Angle FIG. CO ~45BLADE Bevel & 00~45 Miter Angle Using Wood Facing on the RIP Fence FIG. HNCOMPOUNDMITERCROSSCUTTINGFIG.FF Auxiuary Fence FIG. HAttachauxiliaryfenceto ripfencewithtwoCclamps. Fig.dd Fig.JJIA Warn Nen Blade RAISmNG and TmLTmNGMECHANmSM FIGo LLSymptom Possible Causes Corrective ACT!ON IAWARNmNGnParts List for SAW Schematic WAR.I.GSchematic for SAW Parts List and Schematic for Stand SAW ModelParts List and Schematic for Motor Push Stick Construction Page LE-FOYER SU-HOGAR

137.24884 specifications

The Craftsman 137.24884 is a reliable and robust table saw that is ideal for both amateur woodworkers and seasoned professionals. This versatile piece of equipment combines performance, durability, and user-friendly features to cater to a variety of woodworking projects, making it a popular choice in workshops.

One of the most notable features of the Craftsman 137.24884 is its powerful 15-amp motor, which delivers ample cutting power to handle hardwoods, softwoods, and various other materials. The table saw boasts a 10-inch blade that allows for precision cuts and can easily handle rip cuts, crosscuts, and bevel cuts. With a maximum rip capacity of 30 inches, users can tackle larger workpieces with ease, enhancing productivity.

The saw's stability is further complemented by its sturdy cast iron table, which provides a flat and smooth surface for accurate cuts. This enhances the overall performance by minimizing vibrations during operation, ensuring that cuts remain true and consistent. Additionally, the adjustable fence system locks securely in place, allowing users to make precise adjustments and achieve repeatable results.

Safety is a key consideration in the design of the Craftsman 137.24884. It comes equipped with a blade guard and anti-kickback pawls, providing an added layer of protection for users. A push stick is also included, promoting safe operation when handling smaller workpieces.

In terms of portability, the saw features a lightweight design complemented by wheels that facilitate easy movement around the workshop or job site. This portability does not compromise its overall strength and stability, which are crucial for accurate table sawing.

Moreover, the Craftsman 137.24884 incorporates easy-to-access controls, allowing users to quickly change blades or adjust settings. Its onboard storage system keeps essential accessories organized and within reach, enhancing the overall user experience.

In summary, the Craftsman 137.24884 table saw combines powerful performance, precision engineering, and essential safety features, making it an excellent investment for anyone interested in woodworking. This model's durable construction and user-friendly design set it apart as a reliable tool that can tackle both small and large projects effectively. Whether constructing furniture or handling renovations, the Craftsman 137.24884 is a solid choice for precision cut woodworking.
Top Page Image Contents