Zenoah HC510DV manual  14 , Recommended Mixing Ratio Gasoline 50OIL, HOW to MIX Fuel

Page 14

7. Fuel

WARNING

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.

The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE)

Do not use BIA or TCW (2-stroke water- cooling type) mixed oil.

14

RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1

(when using ZENOAH genuine oil)

50:1 MIXING CHART

GASOLINE gal. 1 2 3 4 5

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE

liter

1

2

3

4

5

 

 

 

 

 

 

 

2-CYCLE OIL

ml

20

40

60

80

100

 

 

 

 

 

 

 

Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)

If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate

Image 14
Contents HC510DV 848-C8X-93A1Page Safety First Contents 4  SpecificationsParts location  5  Symbols on the machine  6  7  Before Using the MachineFor safe operation Working Gear and Clothing  8  9  Operation Safety Precautions  10  11  Maintenance Safety PrecautionAfter Using the SAW Change of Dust Stopper Set upSE1  12 Fitting Dust Hose and Dust BAG SE2 SE3 SE4 Mounting of Cutter BladeCutter blade Flange bolt Flange washer a Dust hose Metal band Dust bag Tying CordFuel When using Zenoah genuine oilHOW to MIX Fuel  14 Fueling the Unit For Your Engine LIFE, AvoidClose OperationOP1 OP2 Starting Engine  16  17  OP3 OP4Decomp valve Stopping Engine SwitchOP5 OFFFront guide Horizontal Cutting OP6 OP7 Cutting OperationFor AN Efficient Cutting Operation Vertical CuttingAir cleaner cover Top plate Felt filter MaintenanceAIR Cleaner MA1Spark Plug MA2MA3 NGK BPM8YCooling AIR Passage MA4 MA5 22  Blade Drive BeltBelt Exchange Disassembling ProcedureMA6 MA7 MA8 MA9 Assembling Procedure  24 MA14 FAN Drive Belt Belt Tension Adjustment and ExchangeIdler pulley Belt adjustment plate Bolt Tighten Slacken  25 MA15 Engine Adjustment MA15When adjusting, take the following steps  26  27  Starter Rope Exchange  28 MA19 MA20 MA21 Notch 30  Storage  31  32  Troubleshooting guideCheck Probable Causes Action Parts list  33 Cutter Unit HC510DV S/N 200101 and up  34  35  Power Unit 1 HC510DV S/N 200101 and up  36  37  Power Unit 2 HC510DV S/N 200101 and up  38  39  Carburetor HC510DV S/N 200101 and up  40 Accessories & Tool SET HC510DV S/N 200101 and up  41 Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée