Carrier 50XP manual Options and Accessories, Factory-installed options, Electric Heaters

50XP

OPTIONS AND ACCESSORIES

Factory-installed options

Coil options include Tin-Plated* indoor hairpins, copper/copper and vinyl-coated construction for refrigerant coils. Units are shipped standard with copper tube/aluminum fin construction. See model number nomenclature for coil options.

*Tin-Plated indoor coils are built with special hairpins that are designed to resist both general pitting corrosion and excessive indoor corrosion(Formicary Corrosion).

Field-installed accessories

Economizer with Solid-State Controls and Barometric Relief Dampers

Manual Air Damper (25% open) Electric Heaters

Filter Rack

Flat Roof Curbs (8-in. and 14-in.) (203.2 and 355.6 mm) Square-to-Round Duct Transition Kit Thermidistatt

Thermostats Crankcase Heater

Compressor Start Kit (for use on single-phase units only) Rigging Kit

Low Ambient Kit (Motormaster® II Control)

Solid-State Time Guard® II Device

Lifting Kit

Economizer with solid-state controls and barometric relief dampers includes filter racks and provide outdoor air during cooling and reduce compressor operation.

Manual outside air damper includes hood and filter rack with adjustable damper blade for up to 25% outdoor air.

Electric heaters provide additional heat in the unit when required. Each package has a heater module that slides into the controls

compartment. Heater sizes range from 5.0 to 20.0 kW. The electric heater design allows the use of a single-point power supply for the entire unit, resulting in lower installed costs.

Filter Rack features easy installation, serviceability, and high-filtering performance for vertical or horizontal applications.

Flat roof curbs in both 8 in. (203.2 mm) and 14 in. (355.6 mm) sizes are available for roof mounted applications.

Square-to-round duct transition kit enables 024-048 size units to be fitted to 14 in. (355.6 mm) round ductwork.

Thermidistat Control coupled with the system’s variable speed indoor blower delivers Carrier’s patented IdealHumidity Technology that allows for even greater humidity control. Along with more precisely controlling temperature and humidity, the Thermidistat offers full seven-day programmability allowing you to further customize your comfort and energy savings.

Thermostats provide control for the system heating and cooling functions. Thermostat models are available in both programmable and non-programmable versions.

Crankcase Heater provides anti-floodback protection for low-load cooling applications.

Compressor start kit assists compressor start-up by providing additional starting torque on single phase units and prolongs compressor motor life.

Rigging kit includes lifting brackets which are inserted into the unit base rigging holds to lift unit for rooftop applications.

Low-ambient kit (Motormaster II control) allows the use of mechanical cooling down to outdoor temperatures as low as 0_F (-17_C) when properly installed.

Solid-state Time Guard II device provides short-cycling protection for the compressor. Not required with corporate electronic thermostats.

Lifting kit, including 4 metal brackets that are available to assist in lifting this product onto a roof application.

Electric Heaters

CATALOG	NOMINAL	FUSES			USED WITH SIZES
ORDERING NO.	CAPACITY (kW)		024	030	036	042	048	060
	ELECTRIC HEATERS	(208/230 —	SINGLE PHASE — 60 Hz)
CPHEATER052A00	5.0	0	X	X	X	X	X	X
CPHEATER069A00	7.5	0	X	X	X	X	X	X
CPHEATER065A00	10.0	0	X	X	X	X	X	X
CPHEATER051A00	15.0	4		X	X	X	X	X
CPHEATER053A00	20.0	6				X	X
CPHEATER054A00	20.0	6						X
	ELECTRIC HEATERS	(208/230 —	THREE PHASE — 60 Hz)
CPHEATER055A00	5.0	0		X	X	X	X	X
CPHEATER056A00	10.0	0		X	X	X	X	X
CPHEATER057A00	15.0	0			X	X	X	X
CPHEATER059A00	20.0	6				X	X	X

NOTE: Electric heaters are rated at 240v. Refer to Multiplication Factors table for other voltages.

X = Approved combinations.

Minimum Airflow for Reliable Electric Heater Operation (CFM)

UNIT SIZE	024	030	036	042	048	060
AIRFLOW	750	1000	1250	1400	1500	1800

6