Graco Inc 309410 Trigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatillo, Contractor

Page 3

CONTROLS / CONTROLES / COMMANDES / CONTROLES

On/Off Switch	On/Off Switch Aan/Uit Schakelaar	Pressure Control
Interruptor de ligar e desligar	Interrupteur Marche/Arrêt	Controle da pressão
Interrupteur marche/arrêt	Ein-Aus-Schalter	Système de contrôle de la pression
Interruptor de encendido/apagado		Dispositivo de control de la presión
Interruptor de encendido/apagado		Dispositivo de control de la presión

Engine Controls Controles do motor Commandes de moteur Controles del motor

Trigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatillo

Drain Valve

Válvula de drenagem

Vidange

Válvula de vaciado

ti1852a

On/Off Switch

Interruptor de ligar e desligar Interrupteur marche/arrêt Interruptor de encendido/apagado

Contractor

Contractor II

ti2871a

ti2870a

ti1854a

309410 3

Image 3

Contents 233709 S Controls S Setup S StartupS Cleanup S Pressure Relief S Error Codes 309410 Rev. BADVERTENCIA à la pression maximale de service du systèmeADVERTÊNCIA MISE EN GARDECONTROLS / CONTROLES / COMMANDES / CONTROLES Trigger Lock Fecho do gatilho Loquet de sécurité Seguro del gatilloContractor 309410Change Engine to Motor Setup1. Disconnect engine power cord 2. Release tension bar 4. Install motor drop in and push forward7. Plug in pressure control power cord 6. Secure motor with tension barEngage 4. Remove tip guard 2. Connect other end of hose to gun 3. Tighten securelycold 8. Fill fuel tank 9. Ground sprayer with grounding clamp 5. Install clean inlet strainer6. Fill throat packing nut with TSL to prevent premature packing wear Do this each time you spray and storePAINT FLUSH 3. Set pump switch OFFStartup 2. Turn prime valve down Turn pressure control to lowest pressure4. Start engine a. Move fuel valve to open b. Move choke to closed c. Set throttle to fast d. Set engine switch ON e. Pull starter cordg. Set throttle to desired setting a b c d e f gDo not stop leaks with your hand or a rag! If seat SwitchTip SwitchTip and Guard Assembly1. Engage trigger safety 2. Insert SwitchTipt Insert seat and OneSealtMain Menu Digital Tracking Systemt DTS Operation1. Do Startup steps 1 2. Start engine or motor, pageDigital Tracking System DTS Change Display Units Pressure VolumeWatchDogt Pump Protection System To Activate 1. Do Startup2. Start engine or motor, page 9. Pressure display appears 3. Simultaneously press DTS button and set pump on/off switch onResettable Hour Meter appears 1. Do Startup steps 1. - 3. Pressure must be at zero4. Press and hold to reset to zero, or 12. Turn pump switch OFF at any time to exit stored data mode 9. Short press DTS button again to move to WatchDog MAN manual mode11. Short press to return to step Clearing Tip Clogs Spray Test Pattern3. Turn prime valve down 4. Remove guard and SwitchTip Cleanup1. Set pump switch OFF. Turn engine or motor OFF 2. Turn pressure to lowest setting. Trigger gun to relieve pressure6. Clean filter, guard and SwitchTip in flushing fluid 8. Turn engine ON and start engine or motor. Set pump switch ON 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. Turn pump switch OFF. Turn engine or motor OFF DTS Error Codes Service309409 FOR GRACO CANADA CUSTOMERS Graco WarrantyADDITIONAL WARRANTY COVERAGE Graco Phone Number