Graco Inc 235893, 4600SC, 308-084 Equipment Misuse Hazard, Hazardous Fluid Hazard, Hose Safety

Page 2

WARNINGS

SERIOUS BODILY INJURY, EXPLOSION, FIRE, OR ELECTROST ATIC SHOCK CAN OCCUR IF THE PRECAUTIONS BELOW ARE NOT FOLLOWED.

READ AND UNDERSTAND ALL INSTRUCTION MANUALS, T AGS, AND WARNING LABELS BEFORE OPERATING EQUIPMENT.

ELECTROSTATIC EQUIPMENT SHALL ONLY BE USED BY TRAINED, QUALIFIED PERSONNEL WHO SHALL BE FULL Y CONVERSANT WITH THE REQUIREMENTS STATED WITHIN THIS INSTRUCTION MANUAL.

EQUIPMENT MISUSE HAZARD

General Safety

Any misuse of the spray equipment or accessories, such as over pressurizing, modifying parts, using incompatible chemi- cals and fluids, or using worn or damaged parts, can cause them to rupture and result in serious bodily injury, fire, explosion or property damage.

NEVER point the spray gun at anyone or at any part of the body. NEVER put hand or fingers over the spray nozzle.

ALWAYS follow the Pressure Relief Procedure, at right, before cleaning or removing the fluid nozzle or servicing any system equipment.

NEVER try to stop or deflect leaks with your hand or body.

NEVER alter or modify any part of this equipment; doing so could cause it to malfunction.

CHECK all spray equipment regularly and repair or replace worn or damaged parts immediately.

System Pressure

This gun has a maximum working air and fluid pressure of 100 psi (7 bar). Never exceed the maximum working pressure of the gun or any other component or accessory used in the system.

Fluid Compatibility

BE SURE all fluids and solvents used are chemically compat- ible with the “Wetted Parts” shown in the TECHNICAL DATA. Always read and follow the fluid and solvent manufacturer’s lit- erature before using the fluid or solvent in this gun.

Pressure Relief Procedure

To reduce the risk of serious bodily injury, including splashing in the eyes or on the skin, injury from moving parts or electrostatic shock, always follow this procedure when shutting off the sys- tem, when checking or servicing any part of the spray system, when installing, cleaning or changing fluid nozzles, and when- ever you stop spraying.

1.Turn off all the air to the control module except the manifold air. If the air pilot fluid regulator is used, air pressure is need- ed at the regulator air inlet to relieve pressure in the fluid line.

2.Turn off the fluid supply to the gun.

3.Trigger the gun into a grounded metal waste container to relieve fluid pressure.

4.Open the pump drain valve, having a waste container ready to catch the drainage.

5.Leave the pump drain valve open until you are ready to spray again.

HAZARDOUS FLUID HAZARD

Improper handling of hazardous fluids or inhaling vapors can cause extremely serious bodily injury , even death, due to splashing in the eyes, ingestion, inhalation, or bodily contami- nation. Be sure you know what fluid you are pumping and its specific hazards. Observe all precautions when handling known or potentially hazardous fluids, including, but not limited to, the following precautions.

1.Store hazardous fluids in approved containers.

2.Dispose of any waste fluid according to all Local, State and Federal regulations pertaining to the disposal of hazardous wastes.

HOSE SAFETY

TIGHTEN all fluid connections securely before each use.

NEVER use a damaged hose. Before each use, check the en- tire hose for cuts, leaks, abrasion, bulging cover, or damage or movement of the hose couplings. If any of these conditions exist, replace the hose immediately.

3.Read and follow the fluid and solvent manufacturer’s litera- ture regarding the use of protective clothing and equipment, such as eye protection, respiratory protection, and gloves.

4.Provide for the safe piping and disposal of all exhaust air.

5.Provide proper ventilation in accordance with accepted industry standards and governmental regulations. Refer to Ventilate the Spray Booth, on page 6.

HANDLE AND ROUTE HOSES CAREFULLY. Do not pull on hoses to move equipment. Do not use fluids or solvents which are not compatible with the inner tube and cover of the hose.



Image 2
Contents Part No -894, Series a Part No -224, Series a Air Spray Gun, without shroudPart No -893, Series a Part No -094 Series a Gun ManifoldHazardous Fluid Hazard Hose SafetyEquipment Misuse Hazard FIRE, EXPLOSION, or Electrostatic Shock Hazard Flushing and Cleaning SafetyVentilate the Spray Booth GroundingTable of Contents System Options Typical InstallationInstalling the System Spraying Voltage MonitorInstall the Gun Mounting Bracket InstallationVentilate the Spray Booth Install the Gun and Manifold See FigAccessories section Air Cap/Air Cap NutInstall the Fabric Cover See Fig Check the Electrical Grounding See FigOperation Operating ChecklistAdjusting the Spray Pattern Selecting a Fluid Nozzle and Air Cap Gun FunctionsDaily Care and Cleaning MaintenanceAdjusting the Turbine Air Pressure Activating the Voltage Select KV HI/LOClean the Air Cap and Fluid Nozzle Follow the Pressure Relief Procedure Warning onCheck for signs of fluid leakage where indicated by arrows Check for Fluid Leakage See FigSpray Pattern Troubleshooting Chart Problem Cause Solution Improper Spray PatternGUN Operation Troubleshooting Chart Problem Cause SolutionElectrical Troubleshooting Chart See Check the Electrical GroundingTest Gun Resistance See Fig Test Power Supply Resistance See FigElectrical Tests 40dAir Cap/Nozzle/Resistor Stud Replacement Test Resistor Stud ResistanceFlush the Gun and Relieve Pressure ServiceService Notes Air Cap/Nozzle/Resistor Stud Replacement To install the resistor studElectrode Replacement Barrel Removal Barrel Installation Fluid Packing Rod Removal and Repair   Turbine Alternator Removal Replacement Power Supply Removal and ReplacementPower Supply Adjustment 40cSpray GUN Service Notes Manifold Service Notes Spray GUN Parts Drawing Detail aSpray GUN Parts List Part No -893, Series a Air Spray Gun, with standard shroudManifold Parts List Manifold Parts DrawingPRO 4600HC Conversion KIT Installing the PRO 4600HC Conversion KitSure Relief Procedure on Accessories Mount Extensions 224-255/259 Gun Mount AssemblyVolt Power Supply Nylon Fabric CoverFiber Optic Cables Bulkhead ConnectorGrounding Clamp and Wire MegohmmeterTechnical Data Manual Change SummaryMINNEAPOLIS, MN Graco Warranty and DisclaimersGraco Phone Numbers

308-084, 4600SC, 224-094, 235-894, 235893 specifications

Graco Inc. is a renowned company in the manufacturing of fluid handling systems and products, particularly focusing on industrial, automotive, and contractors' markets. Among its extensive range of offerings are specific models that have garnered attention for their performance and reliability. This article highlights several Graco product numbers, including 224-224, 235893, 235-894, 224-094, and 4600SC.

The model 224-224 is recognized for its versatile usage in paint applications, capable of accommodating various material types. It is equipped with Graco's innovative technology that ensures consistent and precise fluid delivery, making it ideal for both professional contractors and DIY enthusiasts. The device often includes features like a lightweight structure for easy maneuverability and an ergonomic design for enhanced user comfort.

Moving to the model 235893, it presents impressive durability and optimal performance in high-pressure scenarios. This model is particularly popular among heavy-duty applications, thanks to its ability to withstand the rigors of demanding environments. With advanced component engineering, the 235893 ensures minimal downtime and enhances efficiency, making it a go-to choice for professionals in need of reliability under pressure.

The 235-894 model stands out due to its unique pump design that optimizes material flow and reduces overspray. This characteristic is crucial for achieving professional-grade finishes with reduced waste, saving both time and resources. Additionally, its user-friendly interface allows operators to adjust settings easily, catering to varied application needs.

Next, the 224-094 model is tailored for precision and versatility, featuring a compact design suitable for tighter spaces. It is engineered for efficiency, allowing for rapid color changes without compromising performance. The advanced filtration system integrated within this model ensures that contaminants are minimized, safeguarding the integrity of the materials being used.

Lastly, the 4600SC model exemplifies Graco’s commitment to innovation, specifically tailored for airless spray applications. It is equipped with cutting-edge technology that maximizes control over pressure and flow rate, allowing for seamless operation in different environments. The model’s ability to adapt to various paints and coatings while providing a superior finish adds to its appeal.

In summary, Graco Inc. provides a range of high-performance products like the 224-224, 235893, 235-894, 224-094, and 4600SC, each with distinctive features and technologies that cater to a broad spectrum of fluid handling needs. These models reflect the company’s dedication to enhancing efficiency, durability, and user experience in fluid management across various industries.