Grizzly G3358 owner manual Head Crank, Column Cap, Feed Levers

Page 18

Head Crank

The head crank secures to the left side of the machine and is used to adjust the height of the headstock.

To mount the head crank to the machine:

1.Assemble the head crank by attaching the handle in the same method used for the handwheels. Thread the handle into the crank body, then tighten the lock nut.

2.Slide the head crank onto the shaft, then tighten the set screw to secure it in place (Figure 11).

Head Crank

Set Screw

Figure 11. Head crank.

Column Cap

A 6mm hex wrench is needed to install the column cap to the column.

To install the column cap to the column:

1.Slide the column cap over the column and the rack gear that sits on the side of the column.

2.Align the holes of the column cap over the holes in the column.

3.Screw the M8-1.25 x 25 cap screws into the column (Figure 12).

-16-

Figure 12. Properly installed column cap.

Feed Levers

The feed levers control the coarse up and down movement of the spindle

To mount the feed levers to the machine:

1.Screw a black knob onto an end of each of the three chrome feed levers (if not already done).

2.Screw the levers with knobs into the threaded holes on the hub, located on the right side of the machine (Figure 13).

Hub

Lever

Figure 13. Feed levers.

G3358 Milling/Drilling Machine

Image 18
Contents Model G3358 Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Machine Data Sheet Lead Screw Info Features #4/..3!&%49  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%293AFETYYNSTRUCTIONSSFORR-ACHINERY Additional Safety for Mills Machine Care and MaintenanceCircuit Requirements 110/220V OperationItems Needed for Setup SetupSetup Safety Unpacking Description QtyInventory Clean Up Crate Contents Figure QtyMoving & Placing Machine Placement LocationSite Considerations Workbench LoadMountingAssembly HandwheelsTo mount the handwheels to the machine Hardware Recognition Chart Head Crank Column CapFeed Levers Drill Chuck Arbor To install the drill chuckTo install the face mill Face MillTest Run & Break To test run the machineTo break-in the spindle Operation Safety Basic Controls OperationsTable travel controls Head Crank To install a collet or an arbor Collet/ArborTo remove a collet or an arbor To operate the micro-adjustment handwheel Spindle HeightTo lock the spindle Depth Stop To calibrate the depth stopSpeed Changes To change spindle speedsPosition Graduated Dials Cutting Speeds for High Speed Steel HSS Cutting ToolsExample G9299-10 Yuasa-Type Rotary Table AccessoriesH2689-R-8 Quick Change Collet Set G1076-52-PC. Clamping KitG2861-Face Mill G4051-Carbide Insert for Face Mill G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetG9765-9-PC. Ball End Mill Set Schedule MaintenanceCleaning Protecting Daily CheckLubricationV-Belts Points requiring periodic lubrication areService TroubleshootingMotor & Electrical Fan Operation and Work Results To adjust the spring tension Return SpringQuill To adjust the Y-axis leadscrew GibsWiring Electrical Safety InstructionsWiring Diagram Switch Both Sides ShownParts Main Parts Breakdown SeriesMain Parts List DescriptionColumn Gear Cover Base Parts Breakdown Series Base Parts List Label Breakdown and List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%