Grizzly G3358 owner manual Service, Troubleshooting, Motor & Electrical

Page 32

Troubleshooting

SECTION 7: SERVICE

Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel- ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663.

Troubleshooting

Motor & Electrical

Symptom

Possible Cause

Possible Solution

 

 

 

 

 

Machine does not

1.

Plug/receptacle is at fault or

wired 1.

Test for good contacts; correct the wiring.

start or a breaker

 

incorrectly.

 

 

trips.

2.

Motor connection wired incorrectly.

2.

Correct motor wiring connections.

3.Wall fuse/circuit breaker is blown/tripped. 3. Ensure circuit size is suitable for this machine; replace weak breaker.

 

4.

Power supply switched OFF or is at fault.

4.

Ensure power supply is switch on; ensure power

 

 

 

 

supply has the correct voltage.

 

5.

Wiring is open/has high resistance.

5.

Check for broken wires or disconnected/corroded

 

 

 

 

connections, and repair/replace as necessary.

 

6.

Main power switch is at fault.

6.

Replace faulty FWD/OFF/REV switch.

 

7.

Motor is at fault.

7.

Test/repair/replace.

 

 

 

 

 

Machine stalls or is

1.

Feed rate/cutting speed too fast for task.

1.

Decrease feed rate/cutting speed.

overloaded.

2.

Workpiece alignment is poor.

2.

Eliminate workpiece binding; use jig or clamps and

 

 

 

 

position table properly for workpiece alignment

 

 

 

 

control.

 

3.

Wrong cutter type.

3.

Use cutter with correct properties for your type of

 

 

 

 

machining.

 

4.

Motor connection is wired incorrectly.

4.

Correct motor wiring connections.

 

5.

V-belt(s) slipping.

5.

Replace bad V-belt(s).

 

6.

Plug/receptacle is at fault.

6.

Test for good contacts; correct the wiring.

 

7.

Motor bearings are at fault.

7.

Test by rotating shaft; rotational grinding/loose shaft

 

 

 

 

requires bearing replacement.

 

8.

Machine is undersized for the task.

8.

Use smaller sharp cutters/drill bits; reduce the feed

 

 

 

 

rate; reduce the spindle RPM; use cutting fluid if

 

 

 

 

possible.

 

9.

Motor has overheated.

9.

Clean off motor, let cool, and reduce workload.

 

10.

Spindle rotation switch at fault.

10.

Test/repair/replace switch.

 

11.

Motor is at fault.

11.

Test/repair/replace motor.

-30-

G3358 Milling/Drilling Machine

Image 32
Contents Model G3358 Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Identification Machine Data Sheet Lead Screw Info Features #4/..3!&%49  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%293AFETYYNSTRUCTIONSSFORR-ACHINERY Additional Safety for Mills Machine Care and MaintenanceCircuit Requirements 110/220V OperationSetup Setup Safety UnpackingItems Needed for Setup Description QtyInventory Clean Up Crate Contents Figure QtyPlacement Location Site ConsiderationsMoving & Placing Machine Workbench LoadTo mount the handwheels to the machine MountingAssemblyHandwheels Hardware Recognition Chart Feed Levers Head CrankColumn Cap To install the drill chuck To install the face millDrill Chuck Arbor Face MillTo break-in the spindle Test Run & BreakTo test run the machine Operation Safety Basic Controls OperationsTable travel controls Head Crank To remove a collet or an arbor To install a collet or an arborCollet/Arbor To lock the spindle To operate the micro-adjustment handwheelSpindle Height Depth Stop To calibrate the depth stopPosition Speed ChangesTo change spindle speeds Example Graduated DialsCutting Speeds for High Speed Steel HSS Cutting Tools Accessories H2689-R-8 Quick Change Collet SetG9299-10 Yuasa-Type Rotary Table G1076-52-PC. Clamping KitG9765-9-PC. Ball End Mill Set G2861-Face Mill G4051-Carbide Insert for Face MillG5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set Maintenance Cleaning ProtectingSchedule Daily CheckLubricationV-Belts Points requiring periodic lubrication areMotor & Electrical ServiceTroubleshooting Fan Operation and Work Results Quill To adjust the spring tensionReturn Spring To adjust the Y-axis leadscrew GibsWiring Electrical Safety InstructionsWiring Diagram Switch Both Sides ShownParts Main Parts Breakdown SeriesMain Parts List DescriptionColumn Gear Cover Base Parts Breakdown Series Base Parts List Label Breakdown and List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%