Ryobi TS1552DXL manual To Bevel CUT, See Figures 34, Bevel Point Scale Work Clamp

Page 24

OPERATION

nRelease the miter lock plate.

NOTE: You can quickly locate 0°, 22-1/2°left or right, and 45° left or right by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the positive stop notches, located in the miter table frame.

nTighten the miter lock handle securely.

nPlace the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade.

nWhen cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 37.

nAlign cutting line on workpiece with edge of saw blade.

nGrasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible.

nBefore turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

nGrasp the saw handle firmly then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

nSlowly lower the blade into and through the workpiece.

nRelease the switch trigger and allow the blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from the miter table.

TO BEVEL CUT

See Figures 34- 35.

A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the workpiece. A straight bevel cut is made with the miter table set at the zero degree position and the blade set at an angle between 0° and 45°.

nPull out the lock pin and lift saw arm to its full height.

nLoosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

nPress the miter lock plate down with thumb and hold.

nRotate the control arm until the pointer aligns with zero on the miter scale.

nRelease the miter lock plate.

NOTE: You can quickly locate zero by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the built-in positive stop notches, located in the miter table frame.

nTighten the miter lock handle securely.

nAdjustments of the miter fence must be made to cor- respond to the desired angle of the bevel cut prior to tilting the saw arm. The bevel scale is marked for 15°, 30°, and 45°. Loosen the fence screw on the miter fence, slide the fence to the desired position, and retighten the fence screw.

 

 

WORK

 

 

CLAMP

 

 

Fig. 33

 

INDICATOR

 

SCALE

SCREW

 

 

 

INDICATOR

INDICATOR

 

 

 

BEVEL

POINT

 

 

 

SCALE

 

Fig. 34

WORK

CLAMP

Fig. 35

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Electrical Double InsulationElectrical Connection Extension CordsGlossary of Terms Features Product SpecificationsLock Plate Miter Control Lock Handle ARMSwitch Trigger Know Your Compound Miter SAWAMP Motor Blade Wrench StorageTools Needed Loose Parts List HEXNuts Work ClampAssembly UnpackingMounting Holes Trace HolesTo install the work clamp Dust GuideDust BAG Work ClampRear Bracket Table ExtensionsSee Figures 13 Stop Block See Figures 15Stop Block Small Wing Screw Table Base Extension To Install / Replace the Blade See Figures 17Spindle Lock Button LoosenMounting the Laser Guide Aligning the Laser Guide LineLaser Guide Blade Wrench Spindle Broken RED LineSquaring the Miter Table to the Fence See Figures 21Squaring the Blade to the Fence See Figures 25Squaring the Blade to the Miter Table See Figures 29Operation ApplicationsTo Miter Cross CUT/STRAIGHT CROSS- CUT See Figures 32To Bevel CUT See Figures 34Work Bevel Point Scale Work ClampTo Compound Miter CUT To Support Long Workpieces See Figures 3645 X 45 Compound Miter CUT Long Workpiece Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Number of Sides Cutting Crown Molding Laying Molding Flat on the Miter TableCutting Warped Material Clamping Wide WorkpiecesSee Figures 40 WrongAdjustments Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment Depth Stop AdjustmentsMaintenance Positive Stop AdjustmentsGeneral Maintenance Brush ReplacementChanging the Batteries See Figures 46Do not attempt to activate the laser Aperture Laser GuidePage Service Model NO. and Serial no

TS1552DXL specifications

The Ryobi TS1552DXL is a highly regarded table saw designed to meet the needs of both DIY enthusiasts and professional carpenters. With a powerful 15-amp motor, this table saw is capable of handling a wide range of cutting tasks, from simple crosscuts to intricate bevel cuts with precision and ease.

One of the standout features of the TS1552DXL is its large 15-inch maximum rip capacity. This allows users to cut larger sheets of material, making it an ideal choice for those working with plywood or large boards. The saw’s adjustable cutting depths and an included miter gauge provide additional versatility, enabling users to make accurate crosscuts and angled cuts up to 60 degrees.

The Ryobi TS1552DXL is equipped with a foldable stand that enhances stability and portability. This convenient feature allows users to set up and store the saw easily, so it can be moved from one job site to another without hassle. The saw also incorporates a heavy-duty steel frame that not only ensures durability but also provides excellent support when working with larger materials.

Safety is a top priority with the Ryobi TS1552DXL. The saw comes with a blade guard that offers protection during operation while maintaining visibility of the cutting area. Additionally, the built-in push stick and safety switch further enhance user safety, making it a great choice for both seasoned professionals and those new to woodworking.

In terms of technology, the Ryobi TS1552DXL features a rack and pinion system for smooth adjustments. This system allows for quick and easy modifications to the blade height and angle, enabling users to achieve precise cuts consistently. The powerful motor, when combined with a high-quality carbide-tipped blade, delivers clean and efficient cuts, reducing the need for excessive sanding or finishing.

Overall, the Ryobi TS1552DXL boasts a range of features, reliable performance, and user-friendly technologies that make it a standout choice in the world of table saws. Whether you are working on small projects at home or tackling larger jobs on the worksite, this saw offers the reliability and precision needed to get the job done efficiently.
Top Page Image Contents