Ryobi TS1552DXL manual To Compound Miter CUT, See Figure

Page 25

OPERATION

n The 45° triangle on the miter fence provides for the maximum clearance required for adjusting the miter saw’s angle when making a bevel or compound cut.

nLoosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.

nBevel angles can be set from 0° to 45°.

nAlign the indicator point for the desired angle.

nOnce the saw arm has been set at the desired angle, securely tighten the bevel lock knob.

nPlace the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 40 - 41.

nWhen cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 38.

nAlign the cutting line on the workpiece with the edge of saw blade.

nGrasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 35.

nBefore turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

nGrasp the saw handle firmly then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

nSlowly lower the blade into and through the workpiece.

nRelease the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table.

TO COMPOUND MITER CUT

See Figure 36.

A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This type of cut is used to make picture frames, cut molding, make boxes with sloping sides, and for certain roof framing cuts.

To make this type of cut the control arm on the miter table must be rotated to the correct angle and the saw arm must be tilted to the correct bevel angle. Care should always be taken when making compound miter setups due to the interaction of the two angle settings.

Adjustments of miter and bevel settings are interdependent with one another. Each time you adjust the miter setting you change the effect of the bevel setting. Also, each time you adjust the bevel setting you change the effect of the miter setting.

It may take several settings to obtain the desired cut. The first angle setting should be checked after setting the second angle, since adjusting the second angle affects the first.

Once the two correct settings for a particular cut have been obtained, always make a test cut in scrap material before making a finish cut in good material.

C-CLAMP

Fig. 36

nPull out the lock pin and lift saw arm to its full height.

nLoosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

nPress the miter lock plate down with your thumb and hold.

nRotate the control arm until the pointer aligns with the desired angle on the miter scale.

nRelease the miter lock plate.

NOTE: You can quickly locate 0˚, 15˚, 22-1/2˚, left or right, 30˚ and 45˚ left or right by releasing the miter lock plate as you rotate the control arm. The miter lock plate will seat itself in one of the positive stop notches, located in miter table frame.

nTighten the miter lock handle securely.

nAdjustments of the miter fence must be made to cor- respond to the desired angle of the bevel cut prior to tilting the saw arm. The bevel scale is marked for 15°, 30°, or 45°. Loosen the fence screw on the miter fence, slide the fence to the desired position, and retighten the fence screw.

nThe 45° triangle on the miter fence provides for the maxi- mum clearance required for adjusting the miter saw’s angle when making a bevel or compound cut.

nLoosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.

nBevel angles can be set from 0˚ to 45˚.

nOnce the saw arm has been set at the desired angle, securely tighten the bevel lock knob.

nRecheck miter angle setting. Make a test cut in scrap material.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsService Double Insulation ElectricalElectrical Connection Extension CordsGlossary of Terms Product Specifications FeaturesLock Plate Miter Control Lock Handle ARMKnow Your Compound Miter SAW Switch TriggerAMP Motor Blade Wrench StorageTools Needed HEX Loose Parts ListNuts Work ClampUnpacking AssemblyMounting Holes Trace HolesDust Guide To install the work clampDust BAG Work ClampTable Extensions Rear BracketSee Figures 13 See Figures 15 Stop BlockStop Block Small Wing Screw Table Base Extension See Figures 17 To Install / Replace the BladeSpindle Lock Button LoosenAligning the Laser Guide Line Mounting the Laser GuideLaser Guide Blade Wrench Spindle Broken RED LineSee Figures 21 Squaring the Miter Table to the FenceSee Figures 25 Squaring the Blade to the FenceSee Figures 29 Squaring the Blade to the Miter TableApplications OperationTo Miter Cross CUT/STRAIGHT CROSS- CUT See Figures 32See Figures 34 To Bevel CUTWork Bevel Point Scale Work ClampTo Compound Miter CUT See Figures 36 To Support Long Workpieces45 X 45 Compound Miter CUT Long Workpiece Workpiece SupportsCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Laying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialSee Figures 40 WrongPivot Adjustments Travel Pivot Adjustment AdjustmentsBevel Pivot Adjustment Depth Stop AdjustmentsPositive Stop Adjustments MaintenanceGeneral Maintenance Brush ReplacementSee Figures 46 Changing the BatteriesDo not attempt to activate the laser Aperture Laser GuidePage Service Model NO. and Serial no

TS1552DXL specifications

The Ryobi TS1552DXL is a highly regarded table saw designed to meet the needs of both DIY enthusiasts and professional carpenters. With a powerful 15-amp motor, this table saw is capable of handling a wide range of cutting tasks, from simple crosscuts to intricate bevel cuts with precision and ease.

One of the standout features of the TS1552DXL is its large 15-inch maximum rip capacity. This allows users to cut larger sheets of material, making it an ideal choice for those working with plywood or large boards. The saw’s adjustable cutting depths and an included miter gauge provide additional versatility, enabling users to make accurate crosscuts and angled cuts up to 60 degrees.

The Ryobi TS1552DXL is equipped with a foldable stand that enhances stability and portability. This convenient feature allows users to set up and store the saw easily, so it can be moved from one job site to another without hassle. The saw also incorporates a heavy-duty steel frame that not only ensures durability but also provides excellent support when working with larger materials.

Safety is a top priority with the Ryobi TS1552DXL. The saw comes with a blade guard that offers protection during operation while maintaining visibility of the cutting area. Additionally, the built-in push stick and safety switch further enhance user safety, making it a great choice for both seasoned professionals and those new to woodworking.

In terms of technology, the Ryobi TS1552DXL features a rack and pinion system for smooth adjustments. This system allows for quick and easy modifications to the blade height and angle, enabling users to achieve precise cuts consistently. The powerful motor, when combined with a high-quality carbide-tipped blade, delivers clean and efficient cuts, reducing the need for excessive sanding or finishing.

Overall, the Ryobi TS1552DXL boasts a range of features, reliable performance, and user-friendly technologies that make it a standout choice in the world of table saws. Whether you are working on small projects at home or tackling larger jobs on the worksite, this saw offers the reliability and precision needed to get the job done efficiently.
Top Page Image Contents