Ryobi Table Saw manual To Make a Compound Miter CUT, To Make NON-THROUGH Cuts, Featherboard

Page 29

OPERATION

TO MAKE A COMPOUND MITER CUT

It is recommended that you place the piece to be saved on the left side of the blade and that you make a test cut on scrap wood first.

WARNING:

Make sure the blade guard assembly is securely installed and working properly to avoid serious personal injury.

￿Remove the rip fence by lifting the lock down handle.

￿Unlock the bevel locking lever.

￿Adjust the bevel angle to the desired setting.

￿Lock the bevel locking lever.

￿Set the saw blade to the correct depth.

￿Loosen the lock knob on the miter gauge, set the miter gauge to the desired angle and tighten lock knob.

￿Turn the power switch to the on ( ) position.

￿Position the workpiece flat on the table with the edge flush against the miter gauge. Let the blade build up to full speed before feeding the workpiece into the blade.

￿Advance the workpiece and the miter gauge toward the blade. Keep the workpiece flush against the miter gauge. Push the miter gauge and workpiece toward the blade. Stand slightly to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur.

￿When the cut is made, turn the saw off ( ). Wait for the blade to come to a complete stop before removing the workpiece.

￿After the blade has stopped completely, remove the cutoff stock.

TO MAKE NON-THROUGH CUTS

Non-through cuts can be made with the grain (ripping) or across the grain (crosscut). The use of a non-through cut is essential to cutting grooves, rabbets, and dadoes. This is the only type cut that is made without the blade guard installed. Make sure the blade guard assembly is reinstalled upon completion of this type of cut. Read the appropriate section which describes the type of cut in addition to this section on non-through or dado cuts. For example, if your non-through cut is a straight cross cut, read and understand the section on straight cross cuts before proceeding.

FEATHERBOARD

-

+

PUSHSTICK

BEVEL

LOCKING LEVER

PUSHBLOCK

“C” CLAMP

Fig. 39

￿Loosen the two hex nuts at the base of the riving knife. Do not remove hex nuts. Remove the riving knife/ guard assembly. Retighten the two hex nuts on the base.

￿Lower the blade and insert the throat plate, then securely tighten the throat plate screw.

￿Bring the blade back to 90°.

￿Raise the blade to the correct height by turning the blade adjusting handle counterclockwise.

￿Feed the workpiece into the blade.

WARNING:

Carefully check all setups and rotate the blade one full revolution to assure proper clearance before connecting saw to power source.

￿Always use pushblocks, pushsticks, and featherboards when making non-through cuts to avoid the risk of serious injury. See Figure 39.

WARNING:

When making a non-through cut, the cutter is covered by the workpiece during most of the cut. Be alert to the exposed cutter at the start and finish of every cut to avoid the risk of serious personal injury.

WARNING:

Unplug the saw to avoid possible injury.

￿Remove the screw holding the throat plate in place. Remove the throat plate.

￿Raise the saw blade.

￿Put the saw in angle mode by pushing the bevel locking lever to the right. Turn the blade adjusting handle until the blade indicator shows a 30° angle. Push the bevel locking lever securely to the left to lock the angle.

Page 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Wrench #2 Phillips Screwdriver Framing Square UnpackingTools Needed Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Speed and WiringBlades Assembling Wheels and HUB Caps AssemblyAssembling Bumpers WheelOpening the LEG Stand Closing the LEG Stand REMOVING/REPLACING the Throat Plate To Install RIP FenceRIP Fence Front Rail Finger HoleTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts To Remove the Blade Rotate Blade AdjustingBlade Throatguard Plate Push Bevel Locking Locking Lever LeftInch To CHECK, Replace or Adjust the Blade Guard AssemblyRiving Knife Shims HEX Nuts To SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveTo USE Sliding Table Extension To USE Outfeed SupportTo Make a Cross CUT Lower SCALE19 Inch Mark Miter GaugeTo Make a Straight RIP CUT To Make a Miter CUTMiter Gauge RIP Fence Bevel Locking Lever To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To Make NON-THROUGH Cuts To Make a Compound Miter CUTFeatherboard Bevel Locking Lever Pushblock ClampGeneral Maintenance MaintenanceTo Make Dado Cuts LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orStop Bolt Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20R

Table Saw specifications

The Ryobi Table Saw is a powerful and versatile tool designed for both hobbyists and professional woodworkers. Known for its durability and efficiency, this table saw is an essential addition to any workshop. One of its standout features is the high-performance motor, which typically operates at 15 amps, delivering ample power to handle a variety of cutting tasks with ease. This ensures that it can cut through hardwood, softwood, and even plywood without bogging down.

A notable characteristic of the Ryobi Table Saw is its precision. Equipped with a robust aluminum table, the saw offers a flat, sturdy surface that promotes accurate cuts. The table is typically expansive, allowing users to work on larger materials without difficulty. With the inclusion of rack and pinion fence system, users can make quick adjustments to the blade position, ensuring that each cut is clean and precise. The fence system is user-friendly, allowing for smooth adjustments with minimal effort.

Safety is a top priority in Ryobi's design, and this is reflected in various features like the blade guard and anti-kickback pawls. The blade guard provides visibility of the cut line while protecting the user from potential injury. Additionally, the saw often includes a push stick, which helps maintain a safe distance from the blade during operation.

Another key technology found in the Ryobi Table Saw is its portability. Many models are designed to be lightweight and feature wheels, making it easy to move the saw from one location to another. This is particularly advantageous for contractors or those who have limited workshop space.

Dust collection is also an important aspect of woodworking, and the Ryobi Table Saw typically includes a built-in dust port. This enables users to connect a shop vac or dust collector, minimizing the mess and ensuring a cleaner work environment.

In summary, the Ryobi Table Saw integrates powerful performance with user-friendly features. Its precision cutting capabilities, safety mechanisms, and portability make it an excellent tool for anyone looking to tackle woodworking projects. Whether you're a seasoned professional or a DIY enthusiast, the Ryobi Table Saw can elevate your craftsmanship and improve your woodworking efficiency.
Top Page Image Contents