Ryobi Table Saw manual Types of Cuts

Page 21

OPERATION

￿The kerf (the cut made by the blade in the wood) will be wider than the blade to avoid overheating or binding. Make allowance for the kerf when measuring wood.

￿Make sure the kerf is made on the waste side of the measuring line.

￿Cut the wood with the finish side up.

￿Knock out any loose knots with a hammer before making the cut.

￿Always provide proper support for the wood as it comes out of the saw.

TYPES OF CUTS

See Figure 19.

There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the compound (bevel) miter cut. All other cuts are combina- tions of these basic six. Operating procedures for making each kind of cut are given later in this section.

WARNING:

Always make sure the blade guard and anti-kickback pawls are in place and working properly when making these cuts to avoid possible injury.

Cross cuts are straight 90° cuts made across the grain of the workpiece. The wood is fed into the cut at a 90° angle to the blade, and the blade is vertical.

Rip cuts are made with the grain of the wood. To avoid kickback while making a rip cut, make sure one side of the wood rides firmly against the rip fence.

Miter cuts are made with the wood at any angle to the blade other than 90°. The blade is vertical.

WARNING:

Always use a pushstick with small pieces of wood, and also to finish the cut when ripping a long narrow piece of wood, to prevent your hands from getting close to the blade.

Bevel cuts are made with an angled blade. Bevel cross cuts are across the wood grain, and bevel rip cuts are with the grain. The rip fence must always be on the right side of the blade for bevel rip cuts.

Compound (or bevel) miter cuts are made with an angled blade on wood that is angled to the blade. Be thoroughly familiar with making cross cuts, rip cuts, bevel cuts, and miter cuts before trying a compound miter cut.

1

Cross Cut

2

Rip Cut

3

Miter Cut

4

Bevel Cross Cut

5

Bevel Rip Cut

6

Compound (Bevel) Miter Cut

Fig. 19

WARNING:

All blades must be rated for at least 5,500 rpm to prevent possible injury.

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Unpacking Tools NeededWrench #2 Phillips Screwdriver Framing Square Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchSpeed and Wiring BladesPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Assembling Wheels and HUB Caps AssemblyAssembling Bumpers WheelOpening the LEG Stand Closing the LEG Stand REMOVING/REPLACING the Throat Plate To Install RIP FenceRIP Fence Front Rail Finger HoleTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts To Remove the Blade Rotate Blade AdjustingBlade Throatguard Plate Push Bevel Locking Locking Lever LeftTo CHECK, Replace or Adjust the Blade Guard Assembly Riving Knife Shims HEX NutsInch To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveTo USE Sliding Table Extension To USE Outfeed SupportTo Make a Cross CUT Lower SCALE19 Inch Mark Miter GaugeTo Make a Straight RIP CUT To Make a Miter CUTTo Make a Bevel Cross CUT To Make a Bevel RIP CUTMiter Gauge RIP Fence Bevel Locking Lever To Make NON-THROUGH Cuts To Make a Compound Miter CUTFeatherboard Bevel Locking Lever Pushblock ClampGeneral Maintenance MaintenanceTo Make Dado Cuts LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orStop Bolt Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20R

Table Saw specifications

The Ryobi Table Saw is a powerful and versatile tool designed for both hobbyists and professional woodworkers. Known for its durability and efficiency, this table saw is an essential addition to any workshop. One of its standout features is the high-performance motor, which typically operates at 15 amps, delivering ample power to handle a variety of cutting tasks with ease. This ensures that it can cut through hardwood, softwood, and even plywood without bogging down.

A notable characteristic of the Ryobi Table Saw is its precision. Equipped with a robust aluminum table, the saw offers a flat, sturdy surface that promotes accurate cuts. The table is typically expansive, allowing users to work on larger materials without difficulty. With the inclusion of rack and pinion fence system, users can make quick adjustments to the blade position, ensuring that each cut is clean and precise. The fence system is user-friendly, allowing for smooth adjustments with minimal effort.

Safety is a top priority in Ryobi's design, and this is reflected in various features like the blade guard and anti-kickback pawls. The blade guard provides visibility of the cut line while protecting the user from potential injury. Additionally, the saw often includes a push stick, which helps maintain a safe distance from the blade during operation.

Another key technology found in the Ryobi Table Saw is its portability. Many models are designed to be lightweight and feature wheels, making it easy to move the saw from one location to another. This is particularly advantageous for contractors or those who have limited workshop space.

Dust collection is also an important aspect of woodworking, and the Ryobi Table Saw typically includes a built-in dust port. This enables users to connect a shop vac or dust collector, minimizing the mess and ensuring a cleaner work environment.

In summary, the Ryobi Table Saw integrates powerful performance with user-friendly features. Its precision cutting capabilities, safety mechanisms, and portability make it an excellent tool for anyone looking to tackle woodworking projects. Whether you're a seasoned professional or a DIY enthusiast, the Ryobi Table Saw can elevate your craftsmanship and improve your woodworking efficiency.
Top Page Image Contents