Ryobi Table Saw manual Extension Cords, Electrical Connection, Grounding Instructions

Page 7

ELECTRICAL

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong ground- ing plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used.

Length of Extension Cord

Wire Size (A.W.G.)

Up to 25 feet

14

26-50 feet

12

When working with the tool outdoors, use an extension cord that is designed for outside use. This is indicated by the letters WA on the cord's jacket.

Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation. Repair or replace a damaged or worn cord immediately.

CAUTION:

Keep the cord away from the cutting area and position the cord so that it will not be caught on lumber, tools, or other objects during cutting.

ELECTRICAL CONNECTION

Your Ryobi Table Saw is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the saw does not operate when plugged into an outlet, double check the power supply.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live termi- nal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.

Repair or replace a damaged or worn cord immediately.

This tool is intended for use on a circuit that has an outlet like the one shown in Figure 1. It also has a grounding pin like the one shown.

COVER OF GROUNDED

OUTLET BOX

GROUNDING

PIN

Fig. 1

Page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Tools Needed UnpackingWrench #2 Phillips Screwdriver Framing Square Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchBlades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Wheel AssemblyAssembling Wheels and HUB Caps Assembling BumpersOpening the LEG Stand Closing the LEG Stand Finger Hole To Install RIP FenceREMOVING/REPLACING the Throat Plate RIP Fence Front RailTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts Push Bevel Locking Locking Lever Left Rotate Blade AdjustingTo Remove the Blade Blade Throatguard PlateRiving Knife Shims HEX Nuts To CHECK, Replace or Adjust the Blade Guard AssemblyInch To Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveLower SCALE19 Inch Mark Miter Gauge To USE Outfeed SupportTo USE Sliding Table Extension To Make a Cross CUTTo Make a Straight RIP CUT To Make a Miter CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTMiter Gauge RIP Fence Bevel Locking Lever Bevel Locking Lever Pushblock Clamp To Make a Compound Miter CUTTo Make NON-THROUGH Cuts FeatherboardLubrication MaintenanceGeneral Maintenance To Make Dado CutsNuts Clamp Screw RIP Fence Blade Locking Handle Screws To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop BoltProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20R

Table Saw specifications

The Ryobi Table Saw is a powerful and versatile tool designed for both hobbyists and professional woodworkers. Known for its durability and efficiency, this table saw is an essential addition to any workshop. One of its standout features is the high-performance motor, which typically operates at 15 amps, delivering ample power to handle a variety of cutting tasks with ease. This ensures that it can cut through hardwood, softwood, and even plywood without bogging down.

A notable characteristic of the Ryobi Table Saw is its precision. Equipped with a robust aluminum table, the saw offers a flat, sturdy surface that promotes accurate cuts. The table is typically expansive, allowing users to work on larger materials without difficulty. With the inclusion of rack and pinion fence system, users can make quick adjustments to the blade position, ensuring that each cut is clean and precise. The fence system is user-friendly, allowing for smooth adjustments with minimal effort.

Safety is a top priority in Ryobi's design, and this is reflected in various features like the blade guard and anti-kickback pawls. The blade guard provides visibility of the cut line while protecting the user from potential injury. Additionally, the saw often includes a push stick, which helps maintain a safe distance from the blade during operation.

Another key technology found in the Ryobi Table Saw is its portability. Many models are designed to be lightweight and feature wheels, making it easy to move the saw from one location to another. This is particularly advantageous for contractors or those who have limited workshop space.

Dust collection is also an important aspect of woodworking, and the Ryobi Table Saw typically includes a built-in dust port. This enables users to connect a shop vac or dust collector, minimizing the mess and ensuring a cleaner work environment.

In summary, the Ryobi Table Saw integrates powerful performance with user-friendly features. Its precision cutting capabilities, safety mechanisms, and portability make it an excellent tool for anyone looking to tackle woodworking projects. Whether you're a seasoned professional or a DIY enthusiast, the Ryobi Table Saw can elevate your craftsmanship and improve your woodworking efficiency.
Top Page Image Contents