Ryobi SC180VS manual Assembly, Mounting Scroll SAW to Workbench, Clamping Scroll SAW to Workbench

Page 10

ASSEMBLY

Your Ryobi 18 in. (457 mm) Scroll Saw was fully assembled at the factory. Before operating this tool, it is important to check all alignments and settings. Normal handling during shipment may have changed settings.

MOUNTING SCROLL SAW TO WORKBENCH

WARNING:

To avoid serious personal injury from unexpected tool movement, always securely mount scroll saw to a workbench.

If the scroll saw is to be used in a permanent application, we recommend that you secure it in a permanent location such as a workbench. When mounting the saw to a workbench, holes should be drilled through the supporting surface of the workbench.

■Each hole in the base of the saw should be bolted securely using machine bolts, washers, and nuts (not included). Bolts should be of sufficient length to accom- modate the saw base, washers, nuts, and the thickness of the workbench.

■Place scroll saw on workbench. Using the saw base as a pattern, locate and mark the holes where the scroll saw is to be mounted.

■Drill four holes through the workbench.

■Place scroll saw on workbench aligning holes in the saw base with the holes drilled in the workbench.

■Insert all four bolts (not included) and tighten securely with washers and nuts (not included).

Note: All bolts should be inserted from the top. Install the washers and nuts from the underside of the bench.

Supporting surface where scroll saw is mounted should be examined carefully after mounting to insure that no move- ment during use can result. If any tipping or walking is noted, secure workbench or supporting surface before beginning cutting operations.

Reducing Noise and Vibration:

You may wish to place a foam pad or piece of carpet between the saw base and the workbench to help reduce noise and vibration.

If a foam pad or piece of carpet is used, do not overtighten the mounting bolts. Leave some cushion between the pad- ding and the saw base to help absorb the noise and vibration.

The size of the padding material should be approximately 24 in. x 12 in. x 1/2 in. (610 mm x 305 mm x 13 mm).

CLAMPING SCROLL SAW TO WORKBENCH

See Figure 5.

If the scroll saw is to be used in a portable application, it is recommended that you fasten it permanently to a mounting board that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size to avoid tipping of saw while in use. Any good grade plywood or chipboard with a 3/4 in. (19 mm) thickness is recommended.

■Mount saw to board using holes in saw base as a template for hole pattern. Locate and mark the holes where scroll saw is to be mounted.

■Follow last three steps in previous section called Mounting Scroll Saw to Workbench.

If lag bolts are being used, make sure they are long enough to go through holes in the saw base and the material the saw is being mounted to.

If machine bolts are being used, make sure they are long enough to go through holes in the saw base, the material the saw is being mounted to, and the washers and nuts.

Note: It may be necessary to countersink washers and nuts on the bottom side of mounting board.

R

E

STORAG

BLADE

C-CLAMP

SAW BASE

MOUNTING

C-CLAMP

BOARD

WORKBENCH

Fig. 5

Page 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Scroll SAW SC180VS Save this Manual for Future ReferenceProduct Specifications Table of ContentsIntroduction Read ALL Instructions Rules for Safe OperationBlade Coasts After Turn OFF Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Do not Remove Jammed Cutoff Pieces until blade has stoppedSafety and International Symbols MeaningElectrical Connection ElectricalExtension Cords Grounding InstructionsUnpacking Glossary of Terms for WoodworkingSPM Tools Needed Loose PartsPIN Blade Know Your Scroll SAW Clamping Scroll SAW to Workbench AssemblyMounting Scroll SAW to Workbench Clamp SAW Base Mounting Board WorkbenchSquaring the SAW Table to the Blade AdjustmentsDrop Foot Sawdust BLOWER/LIGHTZero Degree Stop Table Lock Knob Bevel Scale Setting the Table for Horizontal or Bevel CuttingZero Degree Stop Assembly Screw HEX NUTRelease Installing BladesTension BladeCutting Procedures Adjusting Drop FootAdjusting Blade Tension OperationAvoiding Injury Removing Jammed MaterialON/OFF Knob with Variable Speed Lock Post Choice of Blade and SpeedBlade Information Lock Post On / OFF KnobInterior Scroll Cutting Scroll CuttingStack Cutting ARM Bearings MaintenanceGeneral Maintenance Motor BrushesTroubleshooting Problem Cause SolutionExtension Cord Caution Ryobi TECHNOLOGIES, INC

SC180VS specifications

The Ryobi SC180VS is a versatile and powerful scroll saw that stands out in the realm of woodworking tools. It is specifically designed to cater to both hobbyists and professionals, delivering precision and ease of use.

One of the most notable features of the SC180VS is its variable speed control, which allows users to adjust the blade speed from 400 to 1,600 strokes per minute. This functionality enables woodworkers to make intricate cuts on various materials, including wood, plastic, and even metal, by simply adjusting the speed to suit the specific project requirements. The ability to customize blade speed enhances control and reduces the chances of material splintering or burning.

The SC180VS comes equipped with a robust 1.2-amp motor that provides efficient power for cutting through different thicknesses of material. Whether you're working on detailed patterns or larger projects, this scroll saw is engineered to perform with reliability. The tilt table, which can be adjusted up to 45 degrees, further enhances versatility, enabling users to make bevel cuts with great precision.

Another standout feature is the easy blade-change mechanism. The SC180VS utilizes a tool-less blade changing system, which allows for quick and hassle-free swapping of blades. This is an essential characteristic when transitioning between different projects, as it minimizes downtime and keeps the workflow moving smoothly.

Safety is also a priority with the Ryobi SC180VS. The saw includes a transparent blade guard that not only protects users from potential hazards but also provides clear visibility of the cutting area. An integrated dust blower helps maintain a clean workspace by keeping sawdust away from the cutting line, ensuring improved accuracy during operation.

The compact design of the SC180VS makes it easy to store and transport, making it an ideal choice for both small workshops and mobile operations. Its stable base and heavy-duty construction ensure durability and reduce vibrations, providing a smooth cutting experience.

Overall, the Ryobi SC180VS is an exceptional scroll saw, combining innovative features, impressive technology, and user-friendly design. Whether you're a beginner or a seasoned woodworker, this machine promises to enhance your crafting experience while delivering exceptional results. With its blend of performance, speed control, and safety features, the SC180VS is a reliable addition to any woodworking toolkit.
Top Page Image Contents