Ryobi SC180VS manual General Maintenance, ARM Bearings, Motor Brushes

Page 18

MAINTENANCE

WARNING:

When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage.

GENERAL MAINTENANCE

■Keep your scroll saw clean.

■After cleaning the table top initially, apply a thin coat of automobile type (paste) wax to the table top so the wood slides easily while cutting.

■Do not allow pitch to accumulate on the saw table. Clean with gum and pitch remover.

ARM BEARINGS

See Figure 17.

Lubricate the arm bearings after the first 10 hours of use. Oil after every 50 hours of use or whenever there is a squeak coming from the bearings.

■Carefully place the saw on its side as shown in Figure 17. Remove the rubber cap from the upper and the lower arm of the saw.

■Squirt a few drops of SAE20 oil around the shaft end and arm bearings. Let oil soak in overnight, remaining in this position.

Note: Lubricate the bearings on the other side of the saw in this same manner.

WARNING:

If the power cord is worn, cut, or damaged in any way, have it replaced immediately by a qualified service technician. Failure to do so could result in serious personal injury.

MOTOR BRUSHES

See Figure 18.

Your saw has externally accessible motor brush assemblies that should be checked periodically for wear. When one of the two brushes becomes worn, replace both brushes.

■Unplug the saw from the power source.

■Carefully place the saw on its side exposing the under- side of the saw housing.

■Using a flat blade screwdriver, remove the bottom brush assembly cap through the access hole in the base and the top brush assembly cap from the top of the motor. Gently pry the brush assemblies out using a small screw drivier, point of a nail, or paper clip.

■If one motor brush is worn down shorter than 1/4 in. (6 mm), replace both motor brushes. Do not replace one side without replacing the other. Make sure curvature of brush matches curvature of motor and that the motor brush moves freely in brush tube. Use the blunt end of something thin (eraser end of pencil, etc.) to push the motor brush into the tube until it stays.

■Make sure the motor brush cap is oriented correctly (straight). Tighten motor brush cap using a hand powered screwdriver only. Do not overtighten.

STORAGE

BLADE

ARM BEARING

MOTOR

BRUSH

BRUSH

CAP

Fig. 18

ARM BEARING

Fig. 17

Page 18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Scroll SAW SC180VS Save this Manual for Future ReferenceTable of Contents Product SpecificationsIntroduction Rules for Safe Operation Read ALL InstructionsBlade Coasts After Turn OFF Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Do not Remove Jammed Cutoff Pieces until blade has stoppedSafety and International Symbols MeaningElectrical Connection ElectricalExtension Cords Grounding InstructionsGlossary of Terms for Woodworking UnpackingSPM Loose Parts Tools NeededPIN Blade Know Your Scroll SAW Clamping Scroll SAW to Workbench AssemblyMounting Scroll SAW to Workbench Clamp SAW Base Mounting Board WorkbenchSquaring the SAW Table to the Blade AdjustmentsDrop Foot Sawdust BLOWER/LIGHTZero Degree Stop Table Lock Knob Bevel Scale Setting the Table for Horizontal or Bevel CuttingZero Degree Stop Assembly Screw HEX NUTRelease Installing BladesTension BladeCutting Procedures Adjusting Drop FootAdjusting Blade Tension OperationRemoving Jammed Material Avoiding InjuryON/OFF Knob with Variable Speed Lock Post Choice of Blade and SpeedBlade Information Lock Post On / OFF KnobScroll Cutting Interior Scroll CuttingStack Cutting ARM Bearings MaintenanceGeneral Maintenance Motor BrushesTroubleshooting Problem Cause SolutionExtension Cord Caution Ryobi TECHNOLOGIES, INC

SC180VS specifications

The Ryobi SC180VS is a versatile and powerful scroll saw that stands out in the realm of woodworking tools. It is specifically designed to cater to both hobbyists and professionals, delivering precision and ease of use.

One of the most notable features of the SC180VS is its variable speed control, which allows users to adjust the blade speed from 400 to 1,600 strokes per minute. This functionality enables woodworkers to make intricate cuts on various materials, including wood, plastic, and even metal, by simply adjusting the speed to suit the specific project requirements. The ability to customize blade speed enhances control and reduces the chances of material splintering or burning.

The SC180VS comes equipped with a robust 1.2-amp motor that provides efficient power for cutting through different thicknesses of material. Whether you're working on detailed patterns or larger projects, this scroll saw is engineered to perform with reliability. The tilt table, which can be adjusted up to 45 degrees, further enhances versatility, enabling users to make bevel cuts with great precision.

Another standout feature is the easy blade-change mechanism. The SC180VS utilizes a tool-less blade changing system, which allows for quick and hassle-free swapping of blades. This is an essential characteristic when transitioning between different projects, as it minimizes downtime and keeps the workflow moving smoothly.

Safety is also a priority with the Ryobi SC180VS. The saw includes a transparent blade guard that not only protects users from potential hazards but also provides clear visibility of the cutting area. An integrated dust blower helps maintain a clean workspace by keeping sawdust away from the cutting line, ensuring improved accuracy during operation.

The compact design of the SC180VS makes it easy to store and transport, making it an ideal choice for both small workshops and mobile operations. Its stable base and heavy-duty construction ensure durability and reduce vibrations, providing a smooth cutting experience.

Overall, the Ryobi SC180VS is an exceptional scroll saw, combining innovative features, impressive technology, and user-friendly design. Whether you're a beginner or a seasoned woodworker, this machine promises to enhance your crafting experience while delivering exceptional results. With its blend of performance, speed control, and safety features, the SC180VS is a reliable addition to any woodworking toolkit.
Top Page Image Contents