Ryobi TS1551 manual To Install Blade

Page 14

ASSEMBLY

TO INSTALL BLADE

See Figures 15 and 16.

(See pages 27 and 28 for Mounting the Laser Guide.)

SPINDLE LOCK

BUTTON

WARNING:

A 12 in. (305 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situa- tions could result in a serious accident and can cause serious personal injury.

￿Unplug your saw.

WARNING:

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

￿Raise saw arm.

￿Loosen screw A on the blade bolt cover.

￿Rotate lower blade guard up and remove screw B. Ro- tate blade bolt cover up and back to expose the blade bolt. See Figure 16.

￿Depress the spindle lock button and rotate the blade bolt until the spindle locks.

￿Using the wrench provided, loosen and remove the blade bolt. See Figure 15.

Note: The blade bolt has left hand threads. Turn blade bolt clockwise to loosen.

￿Remove outer blade washer. Do not remove inner blade washer.

￿Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

￿Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in Figure 16.

￿Replace outer blade washer. The double "D" flats on the blade washers align with the flats on the spindle.

￿Depress spindle lock button and replace blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten.

Fig. 15

SCREW A

SCREW B

BLADE

BOLT

COVER

LOWER

BLADE GUARD

TO

INNER BLADE

WASHER WITH

LOOSEN

DOUBLE "D" FLATS

 

 

FLAT (S)

TO

ON SPINDLE

TIGHTEN

 

BLADE BOLT

BLADE

 

OUTER BLADE WASHER

 

WITH DOUBLE "D" FLATS

 

 

Fig. 16

Page 14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operators Manual Save this Manual for Future ReferenceIntroduction Table of ContentsProduct Specifications Double Insulation Safety and International SymbolsRules for Safe Operation Read ALL Instructions Blade Coasts After Being Turned OFF Glossary of Terms for Woodworking FreehandCombination Square Framing Square UnpackingTools Needed HEX KEY Loose Parts ListDust BAG Blade Wrench HEX KEY BoltAMP Motor FeaturesKnow Your Compound Miter SAW Cutting CapacitiesMiter Lock Handle Blade Wrench / Storage AreaCarrying Handle Spindle Lock Button Electric Brake Positive Stops on Miter Table Bevel Lock Knob Miter FenceDust BAG AssemblyDust Guide Work ClampStop Block Small Wing Screw Extension Miter SAW Base Table ExtensionsStop Block Miter SAW BaseTo Install Blade See Figures 17 AdjustmentsSquaring the Miter Table to the Fence Miter Fence Miter Table Squaring the SAW Blade to the FenceSee Figures 20 Bevel Scale IndicatorMiter Fence Blade Framing Lock Miter Square Plate Bevel Lock Knob Blade Squaring the Blade to the Miter TableSee Figures 25 Blade Combination Miter Miter Square Fence TableOperation Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment ApplicationsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAWCrosscutting Straight Crosscut Work ClampBevel CUT Work Clamp Bevel CUTSee Figures 30 Compound Miter CUT Work Clamp Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Support Long Workpieces Long Workpiece SupportsPitch COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters SideCutting Crown Molding Laying Molding Flat on the Miter TableSee Figures 36 Cutting Warped MaterialClamping Wide Workpieces Right WrongBlade Laser Guide Mounting the Laser GuideAlignment Broken RED LineLaser Guide Cover Screws Aperture Laser GuideChanging the Batteries Laser Guide Support KEY Slot Batteries Negative ApertureGeneral MaintenanceCleaning the Laser LubricationExtension Cord Caution Ryobi TECHNOLOGIES, INC
Top Page Image Contents