Ryobi TS1551 manual Miter Fence Blade Framing Lock Miter Square Plate, Bevel, Scale Indicator

Page 17

ADJUSTMENTS

￿The edge of the square and the saw blade should be parallel as shown in figure 21.

￿If the front or back edge of the saw blade angles away from the square as shown in figures 22 and 23, adjust- ments are needed.

￿Loosen the socket head screws that secure the miter fence to the miter table. See Figure 20.

￿Rotate the miter fence left or right until the saw blade is parallel with the square.

￿Retighten the screws securely and recheck the blade- to-fence alignment.

Your saw has two scale indicators, one on the bevel scale and one on the miter scale. After squaring adjustments have been made, it may be necessary to loosen the indicators screws and reset them to zero. See Figure 24.

MITER

FENCE

 

BLADE

FRAMING

MITER

LOCK

MITER SQUARE

PLATE

TABLE

 

MITER

 

LOCK HANDLE

 

VIEW OF BLADE

 

SQUARE WITH FENCE

Fig. 21

30

 

30

 

 

15

0

15

 

 

INDICATOR

SCREWMITER

SCALE

SCALE

INDICATOR

Page 17

MITER

FENCE

BLADE

MITER FRAMING

TABLE SQUARE

VIEW OF BLADE NOT SQUARE WITH

 

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 22

 

MITER

FENCE

BLADE

MITER FRAMING

TABLE SQUARE

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED Fig. 23

BEVEL

INDICATOR

SCALE

POINT

 

 

INDICATOR

 

SCREW

45

 

15

 

 

0

SCALE

INDICATOR

Fig. 24

Image 17
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsProduct Specifications Double Insulation Safety and International SymbolsRules for Safe Operation Read ALL Instructions Blade Coasts After Being Turned OFF Freehand Glossary of Terms for WoodworkingCombination Square Framing Square UnpackingTools Needed Dust BAG Blade Wrench Loose Parts ListHEX KEY HEX KEY BoltKnow Your Compound Miter SAW FeaturesAMP Motor Cutting CapacitiesCarrying Handle Blade Wrench / Storage AreaMiter Lock Handle Spindle Lock ButtonBevel Lock Knob Positive Stops on Miter TableElectric Brake Miter FenceDust Guide AssemblyDust BAG Work ClampStop Block Table ExtensionsStop Block Small Wing Screw Extension Miter SAW Base Miter SAW BaseTo Install Blade See Figures 17 AdjustmentsSquaring the Miter Table to the Fence Miter Fence Miter Table Squaring the SAW Blade to the FenceSee Figures 20 Bevel Scale IndicatorMiter Fence Blade Framing Lock Miter Square Plate See Figures 25 Squaring the Blade to the Miter TableBevel Lock Knob Blade Blade Combination Miter Miter Square Fence TableBevel Pivot Adjustment Pivot Adjustments Travel Pivot AdjustmentOperation ApplicationsCrosscutting Cutting with Your Compound Miter SAWTo Crosscut with Your Miter SAW Straight Crosscut Work ClampBevel CUT Work Clamp Bevel CUTSee Figures 30 Compound Miter CUT Work Clamp Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Long Workpiece Supports Support Long WorkpiecesCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch SideLaying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialSee Figures 36 Right WrongAlignment Mounting the Laser GuideBlade Laser Guide Broken RED LineChanging the Batteries Laser GuideLaser Guide Cover Screws Aperture Laser Guide Support KEY Slot Batteries Negative ApertureCleaning the Laser MaintenanceGeneral LubricationRyobi TECHNOLOGIES, INC Extension Cord Caution