Ryobi TS1551 manual Cutting Warped Material, Clamping Wide Workpieces, See Figures 36, Right Wrong

Page 26

OPERATION

Bevel

 

Angle

Type of Cut

Setting

 

Left side, inside corner

°1. Top edge of molding against fence

33.852. Miter table set right 31.62°

3. Save left end of cut

 

Right side, inside corner

33.85°

1. Bottom edge of molding against fence

2.

Miter table set left 31.62°

 

3.

Save left end of cut

 

Left side, outside corner

33.85°

1. Bottom edge of molding against fence

2.

Miter table set left 31.62°

 

3.

Save right end of cut

Right side, outside corner

°1. Top edge of molding against fence

33.852. Miter table set right 31.62°

3. Save right end of cut

CUTTING WARPED MATERIAL

See Figures 36 and 37.

When cutting warped material, always make sure it is positioned on the miter table with the convex side against the fence as shown in figure 36.

If the warped material is positioned the wrong way as shown in figure 37, it will pinch the blade near the completion of the cut.

RIGHT

Fig. 36

WRONG

Fig. 37

WARNING:

To avoid a binding condition and to avoid serious personal injury, never position the concave edge of bowed or warped material against the fence.

CLAMPING WIDE WORKPIECES

See Figure 38.

When cutting wide workpieces, such as 6 in. x 2 in. (152 mm x 51 mm), boards should be clamped with a C-clamp as shown in figure 38.

WIDE

BOARD

10

 

 

 

8

9

1 2

 

 

7

1 2

 

 

6

1 2

 

 

5

1 2

 

 

 

1 2

 

 

 

 

4

1 2

2

0

45

30

Fig. 38

Page 26

Image 26
Contents Operators Manual Save this Manual for Future ReferenceIntroduction Table of ContentsProduct Specifications Double Insulation Safety and International SymbolsRules for Safe Operation Read ALL Instructions Blade Coasts After Being Turned OFF Glossary of Terms for Woodworking FreehandCombination Square Framing Square UnpackingTools Needed HEX KEY Loose Parts ListDust BAG Blade Wrench HEX KEY BoltAMP Motor FeaturesKnow Your Compound Miter SAW Cutting CapacitiesMiter Lock Handle Blade Wrench / Storage AreaCarrying Handle Spindle Lock ButtonElectric Brake Positive Stops on Miter TableBevel Lock Knob Miter FenceDust BAG AssemblyDust Guide Work ClampStop Block Small Wing Screw Extension Miter SAW Base Table ExtensionsStop Block Miter SAW BaseTo Install Blade See Figures 17 AdjustmentsSquaring the Miter Table to the Fence Miter Fence Miter Table Squaring the SAW Blade to the FenceSee Figures 20 Bevel Scale IndicatorMiter Fence Blade Framing Lock Miter Square Plate Bevel Lock Knob Blade Squaring the Blade to the Miter TableSee Figures 25 Blade Combination Miter Miter Square Fence TableOperation Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment ApplicationsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAWCrosscutting Straight Crosscut Work ClampBevel CUT Work Clamp Bevel CUTSee Figures 30 Compound Miter CUT Work Clamp Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Support Long Workpieces Long Workpiece SupportsPitch COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters SideCutting Crown Molding Laying Molding Flat on the Miter TableSee Figures 36 Cutting Warped MaterialClamping Wide Workpieces Right WrongBlade Laser Guide Mounting the Laser GuideAlignment Broken RED LineLaser Guide Cover Screws Aperture Laser GuideChanging the Batteries Laser Guide Support KEY Slot Batteries Negative ApertureGeneral MaintenanceCleaning the Laser LubricationExtension Cord Caution Ryobi TECHNOLOGIES, INC