Ryobi BTS15 manual Following items are included with your table saw leg stand

Page 11

LOOSE PARTS LIST

The following items are included with your table saw leg stand.

L

	0
	I
M
D
	D
	D
	J
K	D
B	Q
B

HA

D

G

N

N

C

G

G

H

M

H

DI

H

C

D

GH

Q

N

E P

P

E

F

Fig. 3

A. Storage Bracket	2
B. Screw (1/4-20 x 1/2 in. Pan Hd.)	2
C. Lower Side Brace	2
D. Hex Nut (5/16-18)	28
E. Washer (5/16 in.)	2
F. Leveling Foot	1
G. Leg	4
H. Carriage Bolt (5/16-18 x 3/4 in.)	24
I. Upper Brace	2

J. Hex Nut (1/4-20)	2
K. Washer (1/4 in.)	2
L. Bolt (5/16-18 x 2 in. Hex Hd.)	4
M. Upper Side Brace	2
N. Foot	3
O. Washers	4
P. Hex Nut	2
Q. Lower Brace	2

Page 11

Image 11

Contents Save this Manual for Future Reference Operators ManualTable of Contents Rules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalDouble Insulation Electrical ConnectionAnti-Kickback Pawls Fingers Glossary of TermsWrench #2 Phillips Screwdriver Framing Square Socket Wrench Socket Adjustable WrenchUnpacking Tools NeededKey Description Qty Loose Parts ListFollowing items are included with your table saw leg stand Riving Knife FeaturesGetting to Know Your SAW Operating Components Power SwitchPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Speed and WiringProduct Specifications BladesAssembling Storage Brackets AssemblyAssembling LEG Stand To Mount the Table SAW to the LEG Stand To Install the Blade Adjusting HandleRIP Fence Front Rail Table Lock Knobs To Install RIP FenceTo Install Miter Table To Lock Miter TableAttachment Nuts Tabs Mounting Plate To Check SAW Blade InstallationTo Install Blade Guard Assembly HolesOperation Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard Types of Cuts To SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle Outfeed To USE Outfeed SupportTo USE Solid Table Extension To Make a Cross CUTBlade RIP Fence Outfeed Switch KEYTo Make a Miter CUT To Make a Straight RIP CUTMiter Fence RIP Fence Bevel Locking Lever To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To Make NON-THROUGH Cuts To Make a Compound Miter CUTTo Make Dado Cuts Screw Clamp RIP Fence Blade Screws Locking Handle AdjustmentsREMOVING/REPLACING the Throat Plate To Check the Alignment of the RIP Fence to the BladeTo Remove the Blade Pawls Spreader Blade Aligning Spreader with the BladeBevel Bevel Locking Handle Lever To SET Blade AT 0 orTo Ajust the Sliding Miter Table Assembly To Check Miter Base Parallelism Checking Sliding Miter Table AssemblyTo Check Miter Fence Alignment Making Adjustments to Sliding Miter Table AssemblyTo Adjust QUICK-STOP To Adjust the Miter FenceMaintenance Problem Possible Cause Solution Trouble ShootingRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw BTS15