Ryobi BTS15 manual Rules for Safe Operation, Symbol Meaning

Page 3

RULES FOR SAFE OPERATION

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

Symbol Meaning

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices that may cause property damage.

NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.

IMPORTANT

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest Ryobi AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical Ryobi replacement parts.

WARNING:

Observe all normal safety precautions related to avoiding electrical shock.

WARNING:

WARNING:

Do not attempt to use the tool until you read thoroughly and understand completely the operator’s manual. Pay close attention to the safety rules, including Dangers, Warnings, and Cautions. If you use this tool properly and only for what it is intended, you will enjoy years of safe, reliable service.

The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87.1.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Save this Manual for Future Reference Operators ManualTable of Contents Rules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalDouble Insulation Electrical ConnectionAnti-Kickback Pawls Fingers Glossary of TermsWrench #2 Phillips Screwdriver Framing Square Socket Wrench Socket Adjustable WrenchUnpacking Tools NeededKey Description Qty Loose Parts ListFollowing items are included with your table saw leg stand Features Getting to Know Your SAWRiving Knife Operating Components Power SwitchPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Speed and WiringProduct Specifications BladesAssembly Assembling LEG StandAssembling Storage Brackets To Mount the Table SAW to the LEG Stand To Install the Blade Adjusting HandleRIP Fence Front Rail Table Lock Knobs To Install RIP FenceTo Install Miter Table To Lock Miter TableAttachment Nuts Tabs Mounting Plate To Check SAW Blade InstallationTo Install Blade Guard Assembly HolesOperation HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Types of Cuts To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade Outfeed To USE Outfeed SupportTo USE Solid Table Extension To Make a Cross CUTBlade RIP Fence Outfeed Switch KEYTo Make a Miter CUT To Make a Straight RIP CUTTo Make a Bevel Cross CUT To Make a Bevel RIP CUTMiter Fence RIP Fence Bevel Locking Lever To Make NON-THROUGH Cuts To Make a Compound Miter CUTTo Make Dado Cuts Screw Clamp RIP Fence Blade Screws Locking Handle AdjustmentsREMOVING/REPLACING the Throat Plate To Check the Alignment of the RIP Fence to the BladeTo Remove the Blade Pawls Spreader Blade Aligning Spreader with the BladeBevel Bevel Locking Handle Lever To SET Blade AT 0 orTo Ajust the Sliding Miter Table Assembly To Check Miter Base Parallelism Checking Sliding Miter Table AssemblyTo Check Miter Fence Alignment Making Adjustments to Sliding Miter Table AssemblyTo Adjust QUICK-STOP To Adjust the Miter FenceMaintenance Problem Possible Cause Solution Trouble ShootingRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw BTS15
Top Page Image Contents