Multiquip GX390K1SM32 MRH800GS Inspection, Before Starting, Engine Oil Check, Checking The V-Belt

Page 22

DANGER

NEVER operate the compactorin a confined area or enclosed area structure that does not provide ample free flow of air.

ALWAYS wear approved eye and hearing protection before operating the compactor.

Before Starting

1.Read safety instructions at the beginning of manual.

2.Remove dirt and dust, particularly in theengine cooling air inlet, carburetor and air cleaner.

3.Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

4.Check carburetor for external dirt and dust. Clean with dry compressed air.

5.Check fastening nuts and bolts for tightness.

6.Understand the geographical features and regulations of the job site.

Engine Oil Check

1.To check the engine oil level, place the compactor on secure level ground with the engine stopped.

2.Remove the filler dipstick from the engine oil filler hole (Figure 6) and wipe clean.

MRH800GS — INSPECTION

3.Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

4.If the oil level is low, fill to the edge of the oil filler hole with the recommended oil type (Table 3). Maximum oil capacity is 1.16 quarts (1.1 liters).

Checking The Hydraulic System

1.Check the oil tank level gauge (Figure 7). Oil level should be at the middle indication of the gauge or higher. Fill as required

2.Check the surroundings of the oil tank, hydraulic pump and motor for oil leakage.

Level should be middle of gauge or higher

Figure 7. Hydraulic System Oil Level Gauge

DANGER

Always keep hands and fingers away from pinch points. Do not allow anyone to reach in on dangerous sections of the machine to avoid any accidents.

Checking The V-Belt

1.Remove the 2 bolts, one on each side of the center cover, with a #13 socket wrench. Open the center cover of the machine and support it with the strut by inserting its end to the hole in the base (Figure 8).

2.Check V-belt for proper tension. Insufficient tension causes weak vibration.

 

 

 

Center

 

 

 

Cover

Figure 6. Engine Oil Level

Strut

 

 

 

 

TABLA 4. TIPO DE ACEITE

V-Belt

 

 

 

 

Estación

Temperatura

Tipo de aceite

 

 

 

 

 

Verano

25°C ó más alta

SAE 10W-30

 

 

 

 

 

Primavera/Otoño

25°C~10°C

SAE 10W-30/20

 

 

 

 

Figure 8. Checking V-BeltTension

Invierno

0°C ó más baja

SAE 10W-10

 

 

 

 

PAGE 22 — MQ-MIKASA MRH800GS ROLLER — OPERATION AND PARTS MANUAL — REV. #5 (05/27/08)

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model MRH800GS Proposition 65WARNING Page Table of Contents Best Deal! Order via Internet Dealers Only Parts Ordering ProceduresOrder via Fax Dealers Only MRH800GS Safety Message Alert Symbols MRH800GS Safety Message Alert Symbols General Safety MRH800GS Rules for Safe OperationMRH800GS Rules for Safe Operation MRH800GS Operation and Safety Decals MRH800GS Operation and Safety Decals MRH800GS Roller Specifications MRH800GS Engine Specifications MRH800GS -VIBRATION Roller Dimensions MRH800GS Features MRH800GS -VIBRATION Roller Components MRH800GS Vibration Roller ComponentsMRH800GS -VIBRATION Roller Components MRH800GS Handle BAR/LEVER Components MRH800GS Handle BAR/LEVER Components Handle BAR/LEVER ComponentsMRH800GS Engine Components Initial ServicingPage Engine Oil Check MRH800GS InspectionBefore Starting Checking The Hydraulic SystemChecking Water Tank Checking The Vibrator Oil LevelVibrator Oil Level Plug Checking Levers and HornStarting the Engine MRH800GS OperationElectric Start Recoil Start Starter GripOff Position Vibration Lever TravelingParking WateringUnloading Safety FeaturesStopping LiftingDaily Service Inspection and Maintenance Service TablesMRH800GS Maitenance Spark Plug Roller Inspection and AdjustmentAir Filter MRH800GS Maintenance Vibration Clutch Adjustment Forward and Reverse Travel AdjustmentHydraulic System Inspection and Service MRH-800GS Lubrication Chart Handle Bar Maintenance Vibrator Oil Vibrator Oil MaintenancePage MRH800GS Rollertroubleshooting MRH800GS -TROUBLESHOOTING Engine TroubleshootingAir cleaner not clean? QTY. Column NO. ColumnPart NO. Column Remarks ColumnSuggested Spare Parts Qty DescriptionMRH800GSVIBRATION Roller Decal Placement Decal PlacementPart Name DECAL, Mikasa Mobile DTEMRH800GSVIBRATION Roller Axle Assy Axle AssyDrum Bracket R DrumGear Plate Bearing 6308DUMRH800GSVIBRATION Roller Base Assy Base AssyBase YANMAR-L100 Safety GuardAssy WASHER, Lock M10MRH800GSVIBRATION Roller Front Guard Assy Front Guard AssyFront Guard Flat WASHER, M10Lock WASHER, M10 BumperMRH800GSVIBRATION Roller Side Cover Assy Side Cover AssyRubber Hinge SUPPORT, CoverROD Holder RivetMRH800GSVIBRATION Roller -WATERTANK Assy Water Tank AssyWasher 10.5X21X2 SUS Water TankCAP, Water Tank /MR Nylon NUT M10 SUSMRH800GSVIBRATION Roller Hydraulic System Assy Hydraulic System AssySpiral Tube 11D-350L Filter HeadOIL Element Spiral Tube 11D-400LMRH800GSVIBRATION Roller Hydraulic System Assy COVER, Pipe HOLDER, UpperHOLDER, Lower WASHER, Flat M10 in SYSTEM8MRH800GSVIBRATION Roller Hydraulic Oiltank Assy Hydraulic OIL Tank AssyPacking 1/4 CU OIL TANK, GreenOIL Tank , Orange Level GAUGE/L =60MRH800GSVIBRATION Roller Engine Assy Engine Honda GX390 AssyTightener Pulley SWITCH, Horn Button AssyWire Clamp Bearing 6004DDUMRH800GSVIBRATION Roller Engine ASSY. Engine Honda GX390 ASSY.Clamp TC-150 Wire HarnessSwitch CP, S-1B W/CORD Engine GX390K1SM32MRH800GS Electric Device Electric Device Honda GX390 AssyBattery Cord ROD, BatteryHOLDER, Battery -6,7 MICRO-SWITCH ,700MRH800GSVIBRATION Roller Clutch Vibration Assy Clutch Vibration AssyCounter Bracket LOCK, WireCounter Pulley 130D-3V1 BearingMRH800GSVIBRATION Roller -VIBRATOR Assy Vibrator AssyGear Spacer Vibrating CaseBearing 6308C4 GearMRH800GSVIBRATION Roller Upper Control ARM Assy Upper Control ARM AssyMRH800GSVIBRATION Roller Upper Control ARM Assy MRH800GSVIBRATION Roller Upper Control ARM ASSY.CONT Upper Control ARM ASSY.KEY GUIDE, Wire E/GThrottle Wire Conical Spring Washer M12MRH800GSVIBRATION Roller Lower Control ARM Assy Lower Control ARM AssyMRH800GSVIBRATION Roller Lower Control ARM Assy Honda GX-390K1SM32 Cylinder Head Assy Cylinder Head AssyCover COMP., Head CLIP, Valve GuideGASKET, Cylinder Head PACKING, Head CoverHonda GX-390K1SM32 Cylinder Barrel Assy Cylinder Barrel AssyBOLT, Drain Plug Switch ASSY, OIL LevelSHAFT, Governor ARM PLUG, SealingHonda GX-390K1SM32 Crankcase Cover Assy Crankcase Cover AssyPlain Washer 6MM WEIGHT, GovernorSLIDER, Governor BEARING, RadialHonda GX-390K1SM32 Crankshaft Assy Crankshaft AssyWEIGHT, Balancer WASHER, Lock 8MMHonda GX-390K1SM32 Piston Assy Piston AssyPIN Piston Ring SET, PistonPiston STD CLIP,PISTON PIN 20MMHonda GX-390K1SM32 Camshaft Assy Camshaft AssyROD, Push SPRING, Weight ReturnNUT, Pibot Adjusting ARM, Valve RockerHonda GX-390K1SM32 Recoil Starter Assy Recoil Starter AssySPRING, Ratchet RACHET, StarterSPRING, Friction RETAINER, SpringHonda GX-390K1SM32 FAN Cover Assy FAN Cover AssyCover COMP., FAN CLIP, TubeShroud Honda GX-390K1SM32 Carburetor Assy Carburetor AssyFloat SET Gasket SETValve SET, Float Pilot ScrewHonda GX-390K1SM32 AIR Cleaner Assy AIR Cleaner AssyCOLLAR, AIR Cleaner COVER, AIR CleanerGROMET, AIR Cleaner PACKING, ElbowHonda GX-390K1SM32 Muffler Assy Muffler AssyCAP, Muffler Muffler Comp DBPIPE, Exhaust GASKET, EX. PipeHonda GX-390K1SM32 Fueltank Assy Fuel Tank AssyFuel Filter JOINT, Fuel TankTank COMP., Fuel Ring 14MMHonda GX-390K1SM32 Flywheel Assy Flywheel AssyFlywheel Comp FAN, CoolingPULLEY, Starter NUT, Special 16MMHonda GX-390K1SM32 Ignition Coil Assy Ignition Coil AssyCLAMPER, Cord Coil ASSY., IgnitionSpark Plug CAP GROMMET, CordHonda GX-390K1SM32 Starter Motr Assy Starter Motor AssyHonda GX-390K1SM32 Starter Motor Assy Honda GX-390K1SM32 Control Assy Control AssyARM, Governor Adjusting SpringWire Holder ROD, GovernorHonda GX-390K1SM32 Control BOX Assy Control BOX AssyPanel COMP., Control Regulator ASSY., RectCASE, Control BandHonda GX-390K1SM32 Label Assy Label AssyEmblem Terms and Conditions of Sale Parts Page Mexico United Kingdom United StatesCanada

GX390K1SM32 specifications

The Multiquip GX390K1SM32 is a robust and versatile piece of equipment designed for heavy-duty applications, making it a favorite among contractors and professionals in various industries. At the heart of this unit is a powerful Honda GX390 engine, known for its reliability and impressive performance. This engine provides exceptional torque and power, making it ideal for a wide range of tasks, from construction to landscaping.

One of the standout features of the GX390K1SM32 is its heavy-duty construction, which ensures durability and longevity even in the most challenging environments. The frame and components are designed to withstand wear and tear, reinforcing its reputation as a dependable machine. This durability is complemented by a user-friendly design that prioritizes ease of use. The unit features intuitive controls that allow operators to quickly adjust settings and maximize efficiency on the job site.

The GX390K1SM32 also boasts a unique multi-functional capability. It can be utilized for various applications, including pumping, spraying, and powering equipment, which makes it a truly versatile tool. Its adaptability is enhanced by a range of optional attachments, allowing users to customize the machine to suit specific needs. This flexibility increases productivity and efficiency, reducing the need for multiple pieces of equipment.

In terms of safety, the Multiquip GX390K1SM32 incorporates several features designed to protect the operator and ensure safe operation. These include protective casings and emergency shutoff mechanisms that enhance operational safety. Furthermore, the machine is engineered with an emphasis on stability, making it less prone to tipping or accidents during use.

Another significant aspect of the GX390K1SM32 is its fuel efficiency. The Honda engine is not only powerful but also designed to minimize fuel consumption, which translates into lower operating costs. This efficiency combined with its performance makes it an attractive option for businesses looking to optimize their investment in machinery.

Overall, the Multiquip GX390K1SM32 combines power, versatility, and durability, making it an optimal choice for professionals seeking reliable performance in a myriad of applications. Whether for construction, landscaping, or maintenance tasks, this machine stands out as a top contender in the equipment market. Its impressive features and user-centered design ensure that it can handle the demands of any job with ease and efficiency.
Top Page Image Contents