Multiquip manual R2000H Inspection, Before Starting, Engine Oil Check, Fuel Check

Page 21

CAUTION

NEVER operate the roller in a confined area or enclosed area structure that does not provide ample free flow of air.

ALWAYS wear approved eye and hearing protection before operating the roller.

NEVER place hands or feet inside the guard rings while the engine is running. ALWAYS shut the engine down before performing any kind of maintenance service on the roller.

Before Starting

1.Read safety instructions at the beginning of manual.

2.Clean the roller, removing dirt and dust, particularly the air filter and carburetor.

3.Check theairfilter for dirtanddust. Ifairfilterisdirty,replace air filter with a new one as required.

4.Check carburetor for external dirt and dust. Clean with dry compressedair.

5.Check fastening nuts and bolts for tightness.

Engine Oil Check

1.To check the engine oillevel, placethe roller on secure level ground with the engine stopped.

2.Remove the filler dipstick from the engine oil filler hole (Figure 6) and wipe it clean.

Figure 6. Engine Oil Dipstick (Removal)

R2000H — INSPECTION

3.Insertandremovethedipstickwithoutscrewingitintothefiller neck. Check the oil level shown on the dipstick.

4.If the oil level is low (Figure 7), fill to the edge of the oil filler hole with the recommended oil type (Table 4). Maximum oil

capacity is 400 cc.

Reference manufacturer engine

NOTE manual for specific servicing instructions.

Figure 7 Engine Oil Dipstick (Oil Level)

Table 4. Oil Type

Season

Temperature

Oil Type

 

 

 

Summer

25°C or Higher

SAE 10W-30

 

 

 

Spring/Fall

25°C~10°C

SAE 10W-30/20

 

 

 

Winter

0°C or Lower

SAE 10W-10

 

 

 

Explosive Fuel

CAUTION

Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. DO NOT attempt to refuel the roller if the engine is hot! or running.

Fuel Check

1.Remove the gasoline cap located on top of fuel tank.

2.Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish with unleaded fuel.

3.When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel.

R2000H RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #4 (07/24/08) — PAGE 21

Image 21
Contents Model R2000H Proposition 65WARNING Page Table of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only RH 3.25 in mm LH 1.75 in mm LH 9 in mmDrive to rear roll 25 x 7 x 7 in .5 x17.8 x17.8 cmR2000H Specifications Engine R2000H Roller Dimensions R2000H DimensionsSeriously injured if you do not follow directions Injury to yourself and othersInstructions Always wear approved respiratory protectionRules for Safe Operation Always wear seat belts Rules for Safe OperationEmergencies Never stand below roller when it is being liftedMachine Safety Decals Operation and Safety DecalsRecommended Slope Do not operate this roller on slippery or wet surfacesTipping Rollover Tipping RolloversPage Roller Components R2000H Roller ComponentsFree Wheel Engagement Pin Tie-Down Transport PointsAttach a chain or suitable tie-down R2000H Engine Components Before Starting R2000H InspectionEngine Oil Check Capacity is 400 cc Reference manufacturer engineWater System Check Sit down in the operators seat Place the Choke Lever in the Closed positionStarting the Engine R2000H Operation Ignition SwitchWater Sprinklers Control Place the transmission lever in the neutral positionEmergency Shut-Down R2000H Maintenance LubricationHydrostatic Transmission Steering Adjustment Transmission Control Lever AdjustmentDrive Chains Tension Adjustment Drive ChainsTransmissionV-Belt Adjustment Use a belt tension tester to check the belt tensionScrapers, Cocoa Mats, and Sprinkler Bars Roller Storage R2000H Preparation for Long -TERM StorageR2000H Troubleshooting Roller Engine Troubleshooting R2000H Troubleshooting EnginePart NO. Column NO. ColumnQTY. Column Remarks ColumnR2000H Suggested Spare Parts Name Plate and Decals R2000H Name Plate and DecalsDECAL, MQ R2000H Right DECAL, MQ R2000H LeftDECAL, MQ DECAL, MQ MultiquipBrake Assy R2000H Brake AssyLEVER, Parking Brake Adjustable YokeCAP Screw 5/16 SpacerSteering Assy R2000H Steering AssyHexnut 5/8 CAPFlatwasher 5/8 Washer 5/8Chassis & Covers Assy R2000H Chassis and Covers AssyGUARD, Rear Main Body FramePANEL, Left Side PLATE, ShifterBattery Assy R2000H Battery AssyCLAMP, Battery BatteryCAP Screw 3/8 REDRear Drum Assy R2000H Rear Drum AssyBearing Sprocket 70 ToothSCREW, HEX 5/8 Drive System Assy R2000H Drive System AssyWASHER, Flat 3/8 Honda GX240K1QAE2Clip PULLEY, Engine 6 MMTransmission Assy R2000H Transmission AssyROD, Adjustment Adjustment RODPUMP, Hydrostatic LEVER, Free Flow ReliefWater System Assy R2000H Water System AssyWasher 5/16 Flat W TANK, WaterWasher 5/16 Lock CAP, Plastic Water TankAIR Cleaner Assy Honda GX240K1QAE2 Engine AIR Cleaner AssyGROMMET, AIR Cleaner COVER, AIR CleanerCOLLAR, AIR Cleaner Collar B, AIR CleanerCamshaft Assy Honda GX240K1QAE2 Engine Camshaft AssyROD Push SPRING, Weight ReturnARM Valve Rocker Lifter ValveCarburetor Assy Honda GX240K1QAE2 Engine Carburetor AssyGasket SET PLATE, Lever SettingValve SET, Float Float SETControl Assy Honda GX240K1QAE2 Engine Control AssyROD, Governor ARM, GovernorSPRING, Governor SPRING, Throttle ReturnCrankcase Cover Assy Honda GX240K1QAE2 Engine Crankcase Cover AssyHOLDER, Governor Weight WEIGHT, GovernorPIN, Governor Weight GASKET, Case CoverCrankshaft Assy Honda GX240K1QAE2 Engine Crankshaft Assy90745ZE2600 KEY 6.3 X 6.3 X 961006206000 WEIGHT, BalancerCylinder Barrel Assy Honda GX240K1QAE2 Engine Cylinder Barrel AssySHAFT, Governor ARM Switch ASSY., OIL LevelBOLT, Drain Plug OIL SealCylinder Head Assy Honda GX240K1QAE2 Engine Cylinder Head AssyGUIDE, EX. VALVE, OS, Optional GUIDE, VALVE, OS, OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy Honda GX240K1QAE2 Engine FAN Cover AssyCLIP, Tube CLIP, Wire HarnessShroud GROMMET, Drain HoleFlywheel Assy Honda GX240K1QAE2 Engine Flywheel AssyFlywheel Comp FAN, CoolingNUT, Special 16MM KEY, Special WoodruffFuel Tank Assy Honda GX240K1QAE2 Engine Fueltank AssyJOINT, Fuel Tank Rubber Supporter 107MMGASKET, Fuel Filler CAP FILTER, FuelIgnition Coil Assy Honda GX240K1QAE2 Engine Ignition Coil AssyGROMMET, Wire CLAMP, WireWIRE, Stop Switch 370MM HOLDER, Stop Switch WireStarter Motor Assy Honda GX390K1QAE2 Starter Motor AssyContactor Assy WIRE, Water CoverArmature Clutch OverrunningHonda GX240K1QAE2 Control BOX Assy CLIP, Purse Lock Control BOX AssyTUBE, Fastener FUSE, Blade 15A Alert UNIT, OILMuffler Assy Honda GX240K1QAE2 Engine Muffler AssyProtector COMP., Muffler MufflerPROTECTOR, EX. Pipe PIPE, EXPiston Assy Honda GX240K1QAE2 Engine Piston AssyRing SET, PISTON, STD BOLT, Connecting RODRing SET, PISTON, 0.75, Optional PISTON, StandardRecoil Starter Assy Honda GX240K1QAE2 Engine Recoil Starter AssyRATCHET, Starter PULLEY, Recoil StarterSPRING, Friction SPRING, Starter ReturnEngine Labels Honda GX240K1QAE2 Engine Engine LabelsLABEL, Caution EMBLEM, InternalMARK, CHOKE, External MARK, OIL ALERT, ETerms and Conditions of Sale Parts Page Your Local Dealer is HERE’S HOW to GET Help
Related manuals
Manual 90 pages 18.24 Kb

R2000H specifications

The Multiquip R2000H is a versatile and robust portable generator designed to meet the demands of construction sites, rental industries, and various outdoor events. Known for its reliability and performance, this generator stands out with several key features and technologies that cater to diverse power needs.

One of the main features of the R2000H is its powerful engine. The generator is equipped with a reliable Honda GX390 engine, providing a starting output of 2000 watts and a running output of 1800 watts. This ensures ample power to run essential tools and equipment, such as drills, saws, and lights, effectively and efficiently.

The R2000H showcases advanced inverter technology, which offers clean and stable power that is crucial for sensitive electronic equipment. This feature makes it ideal for job sites where precision and protection of equipment are paramount. Inverter technology also ensures fuel efficiency, allowing for longer run times on a single tank of gas, making it an economical choice for extended use.

Portability is another significant characteristic of the Multiquip R2000H. It is designed with a compact structure and lightweight construction, making it easy to transport from one location to another. The integrated wheels and folding handle allow for smooth mobility, thus enhancing its usability on various job sites or recreational activities.

Additionally, the R2000H is constructed with durability in mind. The robust frame protects the generator from the rigors of job site challenges, while also incorporating features like a quiet muffler to reduce operating noise. This is particularly beneficial for users who need to operate the generator in noise-sensitive environments.

User-friendly controls make the R2000H accessible for novice users, while also providing necessary functionalities for experienced operators. The intuitive panel features multiple outlets, enabling the simultaneous use of different tools, and an easy-to-read fuel gauge that allows users to monitor fuel levels with confidence.

Overall, the Multiquip R2000H combines power, efficiency, and convenience, making it an excellent choice for various applications. Whether powering professional tools on a construction site or providing backup power during outdoor events, this generator is designed to deliver reliable performance with outstanding features and technologies.