Multiquip manual R2000H Operation, Ignition Switch

Page 24

4.Insert the ignition key into the ignition (Figure 14), place key in the start position, when engine starts release key.

Figure 14. Ignition Switch

5.Iftheenginedoesnotstart,repeatsteps1through4 or consult the troubleshooting guide contained in this manual.

6.Let the engine warm for 3 to 5 minutes before using roller. Check for fuel and oil leaks, and noises that would asso- ciate with a loose guard and/or covers.

7.If necessary return the choke knob to the full OPEN position.

OPERATION

1.Release the parking brake by pushing down on the parking brake lever.

2.To make the roller move in a forward direction, move the transmission control lever forward as shown in Figure 15. Make sure lever is securely place into notch.

R2000H — OPERATION

Figure 15. Traveling Forward

3.The speed of the roller is directly proportional to the amount ofpressurebeingappliedtotheleverineachdirection.Travel speed is between 0 and 4 mph (6.4 kph).The transmission controllevermaybemovedforwardorreverseatanyengine speed.However, it should not be moved rapidly as damage to the drive train may result.

4.Furtheradjustmentoftravelspeedcanbemadebychanging engine throttle setting. Maximum speed is attained with maximum engine speed and full forward or reverse lever position. Maximum power is attained with lever just out of neutral position and maximum engine speed

WARNING

Transmission control lever must be in neutral position when starting engine. NEVER engage transmission abruptly because this places unnecessary high loads on all drive line components.

WARNING

The parking brake must be used to hold the roller in the "stopped" condition. The transmission system will not hold the roller in a "stopped" condition.

To slow or stop roller, move the transmission control lever toward

NOTE the neutral position. If roller still cannot be slowed or stopped using the hydraulic braking sys- tem, use the parking brake to slow and then stop the roller.

PAGE 24 —R2000H RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #4 (07/24/08)

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model R2000H Proposition 65WARNING Page Table of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only LH 9 in mm RH 3.25 in mm LH 1.75 in mmDrive to rear roll 25 x 7 x 7 in .5 x17.8 x17.8 cmR2000H Specifications Engine R2000H Dimensions R2000H Roller DimensionsInjury to yourself and others Seriously injured if you do not follow directionsAlways wear approved respiratory protection InstructionsRules for Safe Operation Rules for Safe Operation Always wear seat beltsNever stand below roller when it is being lifted EmergenciesOperation and Safety Decals Machine Safety DecalsDo not operate this roller on slippery or wet surfaces Recommended SlopeTipping Rollovers Tipping RolloverPage R2000H Roller Components Roller ComponentsFree Wheel Engagement Pin Tie-Down Transport PointsAttach a chain or suitable tie-down R2000H Engine Components R2000H Inspection Before StartingEngine Oil Check Capacity is 400 cc Reference manufacturer engineWater System Check Sit down in the operators seat Place the Choke Lever in the Closed positionStarting the Engine Ignition Switch R2000H OperationWater Sprinklers Control Place the transmission lever in the neutral positionEmergency Shut-Down R2000H Maintenance LubricationHydrostatic Transmission Transmission Control Lever Adjustment Steering AdjustmentDrive Chains Tension Adjustment Drive ChainsTransmissionV-Belt Adjustment Use a belt tension tester to check the belt tensionScrapers, Cocoa Mats, and Sprinkler Bars R2000H Preparation for Long -TERM Storage Roller StorageR2000H Troubleshooting Roller R2000H Troubleshooting Engine Engine TroubleshootingNO. Column Part NO. ColumnQTY. Column Remarks ColumnR2000H Suggested Spare Parts R2000H Name Plate and Decals Name Plate and DecalsDECAL, MQ R2000H Left DECAL, MQ R2000H RightDECAL, MQ DECAL, MQ MultiquipR2000H Brake Assy Brake AssyAdjustable Yoke LEVER, Parking BrakeCAP Screw 5/16 SpacerR2000H Steering Assy Steering AssyCAP Hexnut 5/8Flatwasher 5/8 Washer 5/8R2000H Chassis and Covers Assy Chassis & Covers AssyMain Body Frame GUARD, RearPANEL, Left Side PLATE, ShifterR2000H Battery Assy Battery AssyBattery CLAMP, BatteryCAP Screw 3/8 REDR2000H Rear Drum Assy Rear Drum AssyBearing Sprocket 70 ToothSCREW, HEX 5/8 R2000H Drive System Assy Drive System AssyHonda GX240K1QAE2 WASHER, Flat 3/8Clip PULLEY, Engine 6 MMR2000H Transmission Assy Transmission AssyAdjustment ROD ROD, AdjustmentPUMP, Hydrostatic LEVER, Free Flow ReliefR2000H Water System Assy Water System AssyTANK, Water Washer 5/16 Flat WWasher 5/16 Lock CAP, Plastic Water TankHonda GX240K1QAE2 Engine AIR Cleaner Assy AIR Cleaner AssyCOVER, AIR Cleaner GROMMET, AIR CleanerCOLLAR, AIR Cleaner Collar B, AIR CleanerHonda GX240K1QAE2 Engine Camshaft Assy Camshaft AssySPRING, Weight Return ROD PushARM Valve Rocker Lifter ValveHonda GX240K1QAE2 Engine Carburetor Assy Carburetor AssyPLATE, Lever Setting Gasket SETValve SET, Float Float SETHonda GX240K1QAE2 Engine Control Assy Control AssyARM, Governor ROD, GovernorSPRING, Governor SPRING, Throttle ReturnHonda GX240K1QAE2 Engine Crankcase Cover Assy Crankcase Cover AssyWEIGHT, Governor HOLDER, Governor WeightPIN, Governor Weight GASKET, Case CoverHonda GX240K1QAE2 Engine Crankshaft Assy Crankshaft AssyWEIGHT, Balancer 90745ZE2600 KEY 6.3 X 6.3 X 961006206000Honda GX240K1QAE2 Engine Cylinder Barrel Assy Cylinder Barrel AssySwitch ASSY., OIL Level SHAFT, Governor ARMBOLT, Drain Plug OIL SealHonda GX240K1QAE2 Engine Cylinder Head Assy Cylinder Head AssyGUIDE, VALVE, OS, Optional GUIDE, EX. VALVE, OS, OptionalCLIP, Valve Guide GASKET, Cylinder HeadHonda GX240K1QAE2 Engine FAN Cover Assy FAN Cover AssyCLIP, Wire Harness CLIP, TubeShroud GROMMET, Drain HoleHonda GX240K1QAE2 Engine Flywheel Assy Flywheel AssyFAN, Cooling Flywheel CompNUT, Special 16MM KEY, Special WoodruffHonda GX240K1QAE2 Engine Fueltank Assy Fuel Tank AssyRubber Supporter 107MM JOINT, Fuel TankGASKET, Fuel Filler CAP FILTER, FuelHonda GX240K1QAE2 Engine Ignition Coil Assy Ignition Coil AssyCLAMP, Wire GROMMET, WireWIRE, Stop Switch 370MM HOLDER, Stop Switch WireHonda GX390K1QAE2 Starter Motor Assy Starter Motor AssyWIRE, Water Cover Contactor AssyArmature Clutch OverrunningHonda GX240K1QAE2 Control BOX Assy Control BOX Assy CLIP, Purse LockTUBE, Fastener FUSE, Blade 15A Alert UNIT, OILHonda GX240K1QAE2 Engine Muffler Assy Muffler AssyMuffler Protector COMP., MufflerPROTECTOR, EX. Pipe PIPE, EXHonda GX240K1QAE2 Engine Piston Assy Piston AssyBOLT, Connecting ROD Ring SET, PISTON, STDRing SET, PISTON, 0.75, Optional PISTON, StandardHonda GX240K1QAE2 Engine Recoil Starter Assy Recoil Starter AssyPULLEY, Recoil Starter RATCHET, StarterSPRING, Friction SPRING, Starter ReturnHonda GX240K1QAE2 Engine Engine Labels Engine LabelsEMBLEM, Internal LABEL, CautionMARK, CHOKE, External MARK, OIL ALERT, ETerms and Conditions of Sale Parts Page HERE’S HOW to GET Help Your Local Dealer is
Related manuals
Manual 90 pages 18.24 Kb

R2000H specifications

The Multiquip R2000H is a versatile and robust portable generator designed to meet the demands of construction sites, rental industries, and various outdoor events. Known for its reliability and performance, this generator stands out with several key features and technologies that cater to diverse power needs.

One of the main features of the R2000H is its powerful engine. The generator is equipped with a reliable Honda GX390 engine, providing a starting output of 2000 watts and a running output of 1800 watts. This ensures ample power to run essential tools and equipment, such as drills, saws, and lights, effectively and efficiently.

The R2000H showcases advanced inverter technology, which offers clean and stable power that is crucial for sensitive electronic equipment. This feature makes it ideal for job sites where precision and protection of equipment are paramount. Inverter technology also ensures fuel efficiency, allowing for longer run times on a single tank of gas, making it an economical choice for extended use.

Portability is another significant characteristic of the Multiquip R2000H. It is designed with a compact structure and lightweight construction, making it easy to transport from one location to another. The integrated wheels and folding handle allow for smooth mobility, thus enhancing its usability on various job sites or recreational activities.

Additionally, the R2000H is constructed with durability in mind. The robust frame protects the generator from the rigors of job site challenges, while also incorporating features like a quiet muffler to reduce operating noise. This is particularly beneficial for users who need to operate the generator in noise-sensitive environments.

User-friendly controls make the R2000H accessible for novice users, while also providing necessary functionalities for experienced operators. The intuitive panel features multiple outlets, enabling the simultaneous use of different tools, and an easy-to-read fuel gauge that allows users to monitor fuel levels with confidence.

Overall, the Multiquip R2000H combines power, efficiency, and convenience, making it an excellent choice for various applications. Whether powering professional tools on a construction site or providing backup power during outdoor events, this generator is designed to deliver reliable performance with outstanding features and technologies.
Top Page Image Contents