Transmission Control Lever Adjustment

R2000H — MAINTENANCE

Brake Adjustment

If the roller tends to creep when the control lever is in neutral, perform the following. Refer to Figure 21 for location of compo- nents.

Figure 21. Control Lever Adjustment Points

1.Place the unit where there is ample clearance fore and aft.

2.Open the cover, place the control lever to neutral position, and remove cotter pin from rod.

3.Start engine and allow to run at idle speed.

4.Move control lever in reverse until roller just starts to move backwards.

5.Carefully hold the control lever in place and turn the engine off.

6.Withoutdisturbingsettingofcontrollever/transmissionarm, add washers on rod between cotter pin hole and grid tube and replace cotter pin.

7.Return control lever to neutral position.

8.Check position of guide tube rod in arm slot. If not centered, remove end of link from arm, loosen lock nuts, adjust length by screwing ends in or out until ball stud drops in arm in centered position.

9.Tighten all nuts.

10.Restartengineandmakesuretransmissionoutputsprocket does not move, at all engine speeds.

1.The brake should be adjusted so that it takes 70 ± 5 lbs. of force applied at the end of the lever to fully actuate it.

2.To adjust brake, turn the knob located at the top of the brake lever clockwise (toward the operator) to tighten the brake.

3.Turn the knob counterclockwise (away from the operator) to loosen the brake.

Steering Adjustment

1.The roller chain of the steering mechanism must be kept clean, lightly oiled and properly tensioned.

2.Adjust the turnbuckle to allow 1/16" deflection to the slack side of the chain when in the straight position.

Drive Chains

1.The drive chains must be kept clean, lightly-oiled, and properly tensioned.

2.When wear of the side bars, rollers or sprockets become noticeable, they should be replaced promptly.

3.Clean all dirt from the chain with solvent and re-oil lightly.

Drive Chains Tension Adjustment

1.Move the roller slowly in the reverse direction until the slack side of the chain is toward the rear of the roller.

2.Put the control lever in the neutral position and shut the engine off and apply parking brake.

3.Loosenthetwoboltsthatholdtheidlerplateforward(intothe chain) using a pry bar.

4.Retighten the two mounting bolts.

5.Start the engine and move the roller in the forward direction, 5 to 10 feet.

6.Move the control lever to the neutral position and turn the engine off.

7.Properchaintensionisapproximately0.2to0.4-inchdeflec- tionwithapproximately5lbs.offorceappliedtothecenterof thespanbetweenthesprocketstowardthefrontoftheroller.

8.If the tension is still incorrect, readjust.

R2000H RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #4 (07/24/08) — PAGE 27

R2000H specifications

The Multiquip R2000H is a versatile and robust portable generator designed to meet the demands of construction sites, rental industries, and various outdoor events. Known for its reliability and performance, this generator stands out with several key features and technologies that cater to diverse power needs.

One of the main features of the R2000H is its powerful engine. The generator is equipped with a reliable Honda GX390 engine, providing a starting output of 2000 watts and a running output of 1800 watts. This ensures ample power to run essential tools and equipment, such as drills, saws, and lights, effectively and efficiently.

The R2000H showcases advanced inverter technology, which offers clean and stable power that is crucial for sensitive electronic equipment. This feature makes it ideal for job sites where precision and protection of equipment are paramount. Inverter technology also ensures fuel efficiency, allowing for longer run times on a single tank of gas, making it an economical choice for extended use.

Portability is another significant characteristic of the Multiquip R2000H. It is designed with a compact structure and lightweight construction, making it easy to transport from one location to another. The integrated wheels and folding handle allow for smooth mobility, thus enhancing its usability on various job sites or recreational activities.

Additionally, the R2000H is constructed with durability in mind. The robust frame protects the generator from the rigors of job site challenges, while also incorporating features like a quiet muffler to reduce operating noise. This is particularly beneficial for users who need to operate the generator in noise-sensitive environments.

User-friendly controls make the R2000H accessible for novice users, while also providing necessary functionalities for experienced operators. The intuitive panel features multiple outlets, enabling the simultaneous use of different tools, and an easy-to-read fuel gauge that allows users to monitor fuel levels with confidence.

Overall, the Multiquip R2000H combines power, efficiency, and convenience, making it an excellent choice for various applications. Whether powering professional tools on a construction site or providing backup power during outdoor events, this generator is designed to deliver reliable performance with outstanding features and technologies.